Abstract:Ti-4Al-4Mo-4Sn-xSi (wt%) (x = 0, 0.2, 0.5) alloys were fabricated by hot extrusion of compacts of blends of TiH2, AlMo60 master alloy and other required elemental powders followed by heat treatments involving vacuum annealing, solution treatment, air cooling and aging. The microstructure of the alloys consists of α plates, lamellae of α and transformed β structure (βt), βt blocks as well as grain boundary α layers. With the addition of 0.2 wt%Si, the Si atoms exist in equal concentration in both α and βt regions as solute atoms, and they retard the growth of α phase, causing a decrease of the average thickness of α plates and lamellae and slight increase of the volume fraction of βt lamellae and blocks. The solid solution strengthening and enhanced α/β interface hardening brought by the 0.2 wt%Si cause the yield strength of the Ti-4Al-4Mo-4Sn alloy to increase significantly from 1030 to 1130 MPa with a slight decrease of the tensile ductility (7.4% vs 6.8%) and without changing the fracture behavior. With the addition of 0.5 wt%Si, the extra Si causes nanometer sized silicide (Ti5Si3) precipitates to form in both α and βt regions and further microstructural refinement. The additional α/β interface hardening and precipitation hardening cause the yield strength of the alloy to increase further to 1177 MPa, but the tensile ductility deteriorates clearly with the elongation to fracture decreasing to 4.9%. The main reason for this ductility decrease is the premature fracture of grain boundary α layers caused by the higher flow stress which can induce more strain localization at the grain boundary α layers.

Study on microstructure and properties of Ti-8.15Si alloy

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Influence Of Annealing Temperature On Film Morphology And Tribological Performance Of Tisin-Ag Coating

Effect of silicon addition on microstructure and mechanical properties of a high strength Ti-4Al-4Mo-4Sn alloy prepared by powder metallurgy

On the Orientation Relationship Between Ti5Si3 Precipitates and B2 Phase in a Ti-47Al-2W-0.5Si Alloy

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Microstructures and mechanical properties of in-situ TiB2/Al−xSi−0.3Mg composites

Microstructure and mechanical properties of Si micro-alloyed (Ti28Zr40Al20Nb12)100-xSix (x=0, 0.1, 0.2, 0.5) high entropy alloys

In-Situ Observation of Ni-11.5wt%Si Eutectic Microstructure Evolution and Exploration of Strengthening Mode of Ni-Ni3si Eutectic Composites

The effects of Ti on the precipitation evolution and age-hardening behavior of Al–7Si–Mg alloy

Effects of metalloid Si on the microstructure and mechanical properties of Fe36Ni36Cr10Mo1Al17-XSiX alloys

Microstructure and Performance of Al-Si Alloy with High Si Content by High Temperature Diffusion Treatment

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Effect of TiB2 and Al3Ti on the microstructure, mechanical properties and fracture behaviour of near eutectic Al-12.6Si alloy

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Microstructure characterization and tensile performance of a high-strength titanium alloy with in-situ precipitates of Ti5Si3

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Precipitation behavior and strengthening-toughening mechanism of hot rolled sheet of Ti65 titanium alloy during aging process

Microstructure characterization and mechanical properties of in situ synthesized Ti2(Al,Si)C reinforced Al composites

Modification mechanism and tensile property of Al-9Si-0.4Mg-0.1Cu alloy