Abstract:The influence of temperature and strain rate on the hot tensile properties of 0Cr18AlSi ferritic stainless steel, a potential structural material in the ultra-supercritical generation industry, was investigated at temperatures ranging from 873 to 1123 K and strain rates of 1.7 × 10−4–1.7 × 10−2 s−1. The microstructural evolution linked to the hot deformation mechanism was characterized by electron backscatter diffraction (EBSD). At the same strain rate, the yield strength and ultimate tensile strength decrease rapidly from 873 K to 1023 K and then gradually to 1123 K. Meanwhile, both yield strength and ultimate tensile strength increase with the increase in strain rate. At high temperatures and low strain rates, the prolonged necking deformation can be observed, which determines the ductility of the steel to some extent. The maximum elongation is obtained at 1023 K for the strain rates of 1.7 × 10−3 and 1.7 × 10−2 s−1, while this temperature is postponed to 1073 K once decreasing the strain rate to 1.7 × 10−4 s−1. Dynamic recovery (DRV) and continuous dynamic recrystallization (CDRX) are found to be the main softening mechanisms during the hot tensile deformation. With the increase of temperature and the decrease of strain rate (i.e., 1123 K and 1.7 × 10−4 s−1), the sub-grain coalescence becomes the main mode of CDRX that evolved from the sub-grain rotation. The gradual decrease in strength above 1023 K is related to the limited increase of dynamic recrystallization and the sufficient DRV. The area around the new small recrystallized grains on the coarse grain boundaries provides the nucleation site for cavity, which generally results in a reduction in ductility. Constitutive analysis shows that the stress exponent and the deformation activation energy are 5.9 and 355 kJ·mol−1 respectively, indicating that the dominant deformation mechanism is the dislocations motion controlled by climb. This work makes a deeply understanding of the hot deformation behavior and its mechanism of the Al-bearing ferritic stainless steel and thus provides a basal design consideration for its extensive application.

Mechanical behavior of stainless steel Cr12Mn5Ni4Mo3Al at high temperature and strain rate

Research on the thermal plasticity of the 18Mn-18Cr-0.77N-2Mo high nitrogen austenitic stainless steel

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Dynamic Mechanical Behavior and Constitutive Model of Stainless Steel

Tensile Properties and Microstructural Evolution of an Al-Bearing Ferritic Stainless Steel at Elevated Temperatures

Dynamic Mechanical Behavior of 6061 Al Alloy at Elevated Temperatures and Different Strain Rates

Experimental study of dynamic properties of 30CrMnSiA steel at high temperature

Modeling the constitutive relationship of Cr 20Ni 25Mo 4Cu superaustenitic stainless steel during elevated temperature

Dynamic Mechanical Behavior at Elevated Temperatures and High Strain Rates of Low Yield Point Steels

Temperature-Dependent Tension Plastic Deformation and Fracture Behavior of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates

High strain rate mechanical behavior of Ti-6Al-4V with micro–macro correlation under compressive loading

High Temperature Deformation Behavior of Ti–46Al–2Cr–4Nb–0.2Y Alloy

Dynamic compressive properties and underlying failure mechanisms of selective laser melted Ti-6Al-4V alloy under high temperature and strain rate conditions

High Temperature Deformation Characteristics of an Alumina‐Forming Stainless Steel

Dynamic tensile behavior of 5CrMnMo at elevated temperatures

High Temperature Deformation Behavior and Constitutive Modelling for 05cr17ni4cu4nb Stainless Steel

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Dynamic behavior of SUS304 stainless steel at elevated temperatures

Study on Dynamic Compressive Mechanics Behavior of TC17 Titanium Alloy at High Temperature and High Strain Rates

Thermo-viscoplastic behavior and constitutive relations for 304 austenitic stainless steel over a wide range of strain rates covering quasi-static, medium, high and very high regimes

High temperature deformation behaviour of Ti–5Al–5Mo–5V–3Cr during thermomechanical processing