Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Identification of Material Parameters for High Strength Steel under Impact Loading

Identification of Dynamic Constitutive Parameters of a High-Strength Steel and Numerical Simulation

Identification of material parameters at high strain rates using ballistic impact tests and inverse finite element analysis

Research on dynamic deformation behavior and constitutive relationship of hot forming high strength steel

0610 A Comparative Study on Gao-Zhang and Johnson-Cook Constitutive Models

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Investigations on the Johnson-Cook Constitutive and Damage-Fracture Model Parameters of a Q345C Steel

Effect of Material Anisotropy on the Mechanical Response of Automotive Steel under High Strain Rates

Material Behavior Description for a Large Range of Strain Rates from Low to High Temperatures: Application to High Strength Steel

Dynamic deformation behavior and corresponding constitutive model of ultra-high strength DP1000 steel

Physical Based Constitutive Model for the Prediction of Plastic Deformation of Fe‐Cr‐Ni Stainless Steel Under High Strain Rate

The investigation on Johnson-Cook model and dynamic mechanical behaviors of ultra-high strength steel M54

Effectiveness of thermoviscoplastic material models in predicting the thermomechanical behavior of rolled homogenous armor steel

Comparative Study on Several Constitutive Models of GCr15 Steel at High Strain Rates

A modified parallel-sided shear zone model for determining material constitutive law

Identification of Multiple Parameters of the Bammann–Chiesa–Johnson Constitutive Model with Comprehensive Experiments for Pure Aluminum

Parametric Analysis and Improvement of the Johnson-Cook Model for a TC4 Titanium Alloy

Modified Johnson-Cook Constitutive Model for Dynamic Compressive Behaviors of C250 Maraging Steel at Different Temperatures

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Determination of the Johnson-Cook Constitutive Model Parameters of Materials by Cluster Global Optimization Algorithm

Experimental Development of Johnson–Cook Strength Model for Different Carbon Steel Grades and Application for Single‐Pass Hot Rolling