Hexagonal Single Crystal Growth of Wo3 Nanorods along A [110] Axis with Enhanced Adsorption Capacity

Jian Zhu,Songling Wang,Songhai Xie,Hexing Li

DOI: https://doi.org/10.1039/c1cc00064k

IF: 4.9

2011-01-01

Chemical Communications

Abstract:Hexagonal single crystal WO(3) nanorods with dominant (001) and (1 ̄10) facets were synthesized, which exhibited high adsorption capacities for organic dyes.

What problem does this paper attempt to address?

One-dimensional Sub-stoichiometric W3O8Nanowires Filled Carbon Nanotubes

Wu Qiuqin,Yao Fenfa,Jin Chuanhong,Zheng Yifan

DOI: https://doi.org/10.15541/jim20210139

IF: 1.292

2022-01-01

Journal of Inorganic Materials

Abstract:Nanostructured sub-stoichiometric transition metal oxides hold promising applications in many areas, while challenge still remains towards their precisely controlled synthesis, particularly for those ultrafine nanowires. In present work, a carbon nanotube (CNT) inner growth based on two-step synthetic approach was adopted to achieve one-dimensional sub-stoichiometric tungsten oxides. Ammonium tetrathiotungsten((NH4)(2)WS4)) were encapsulated into the inner cavity of carbon nanotubes, which were thermally decomposed into tungsten oxides inside the CNTs. Characterizations confirm that the CNT-filling products are ultrafine one-dimensional W3O8 nanowires, that appears 1.23-1.93 nm in width (corresponding to four-five arrays of tungsten atomic column) and up tens of microns in length (close to that of CNTs). The non-noticeable size-dependent lattice parameters of the W3O8 nanowires and the large nanowire-CNT separation indicate a rather weak interaction between the filled W3O8 nanowires and host CNTs, which provides the opportunity to separate and probe the intrinsic properties of these ultrafine 1D W3O8 nanowires. Nevertheless, the proposed synthetic method is extendable to achieve other 1D transition metal oxides.
Novel route to WOx nanorods and WS2 nanotubes from WS2 inorganic fullerenes.

Yan-Hui Li,Yi Min Zhao,Ren Zhi Ma,Yan Qiu Zhu,Niles Fisher,Yi Zheng Jin,Xin Ping Zhang

DOI: https://doi.org/10.1021/jp062427j

2006-01-01

Abstract:WO(x) (2 < x < 3) and WS(2) nanostructures have been widely praised due to applications as catalysts, solid lubricants, field emitters, and optical components. Many methods have been developed to fabricate these nanomaterials; however, most attention was focused on the same dimensional transformation from WO(x) nanoparticles or nanorods to WS(2) nanoparticles or nanotubes. In a solid-vapor reaction, by simply controlling the quantity of water vapor and reaction temperature, we have realized the transformation from quasi-zero-dimensional WS(2) nanoparticles to one-dimensional W(18)O(49) nanorods, and subsequent sulfuration reactions have further converted these W(18)O(49) nanorods into WS(2) nanotubes. The reaction temperature, quantity of water vapor, and pretreatment of the WS(2) nanoparticle precursors are important process parameters for long, thin, and homogeneous W(18)O(49) nanorods growth. The morphologies, crystal structures, and circling transformation mechanisms of sulfide-oxide-sulfide are discussed, and the photoluminescence properties of the resulting nanorods are investigated using a Xe lamp under an excitation of 270 nm.
Novel Route to WOxNanorods and WS2Nanotubes from WS2Inorganic Fullerenes

Yan-Hui Li,Yi Min Zhao,Ren Zhi Ma,Yan Qiu Zhu,Niles Fisher,Yi Zheng Jin,Xin Ping Zhang

DOI: https://doi.org/10.1021/jp062427j

2006-01-01

Abstract:WOx (2 < x < 3) and WS2 nanostructures have been widely praised due to applications as catalysts, solid lubricants, field emitters, and optical components. Many methods have been developed to fabricate these nanomaterials; however, most attention was focused on the same dimensional transformation from WOx nanoparticles or nanorods to WS2 nanoparticles or nanotubes. In a solid-vapor reaction, by simply controlling the quantity of water vapor and reaction temperature, we have realized the transformation from quasi-zero-dimensional WS2 nanoparticles to one-dimensional W18O49 nanorods, and subsequent sulfuration reactions have further converted these W18O49 nanorods into WS2 nanotubes. The reaction temperature, quantity of water vapor, and pretreatment of the WS2 nanoparticle precursors are important process parameters for long, thin, and homogeneous W18O49 nanorods growth. The morphologies, crystal structures, and circling transformation mechanisms of sulfide-oxide-sulfide are discussed, and the photoluminescence properties of the resulting nanorods are investigated using a Xe lamp under an excitation of 270 nm.
Controllable synthesis of hexagonal WO3 nanorod-cluster films with high electrochromic performance in NIR range

Likun Wang,Yong Liu,Gaorong Han,Hongli Zhao

DOI: https://doi.org/10.1016/j.jallcom.2021.161833

IF: 6.2

2022-01-01

Journal of Alloys and Compounds

Abstract:Hexagonal WO3 (h-WO3) nanorod-cluster films were controllably synthesized by a facile template-free hydrothermal technique. The pH value and the amount of urea in the precursor have critical influences on the crystal form and morphology of the WO3 film. The obtained uniform WO3 films feature a porous structure of clusters composed of h-WO3 nanorods with diameter of 6-10 nm and length of up to several hundred nanometers. Due to the novel microstructure and crystalline phase, the high electrochromic performance in NIR range with a high optical modulation of 46% in 1600 nm, fast switching speed (2.4 s for coloration and 3.6 s for bleaching), high coloration efficiency (106.1 cm(2) C-1 in 1600 nm), and an excellent cycling stability (more than 96% charge capacity retained after 1000 cycles) was achieved. (C) 2021 Elsevier B.V. All rights reserved.
An “edge to Edge” Jigsaw-Puzzle Two-Dimensional Vapor-Phase Transport Growth of High-Quality Large-Area Wurtzite-Type ZnO (0001) Nanohexagons

Jian-Min Li,Long-Gui Dai,Xiao-Ping Wan,Xian-Lin Zeng

DOI: https://doi.org/10.1063/1.4761942

IF: 4

2012-01-01

Applied Physics Letters

Abstract:The authors reported the synthesis of large but thin transparent regularly shaped single-crystalline zinc oxide (ZnO) (0001) hexagonal nanodisks (or nanohexagons) (the most probable area scale of 95 μm2 and 40–70 nm in thickness) by an indium assisted vapor-phase transport (VPT) growth route at ambient pressure. These large-area ZnO nanohexagons exhibit excellent luminescent properties with a strong ultraviolet emission band centered at about 384 nm and a very weak green band shoulder emission, leading to the further creation of a promising low-defect-concentration nanohexagons-based nanooptoelectronics. Finally, a two-dimensional VPT growth mechanism was proposed to understand the formation of high-quality wurtzite-type ZnO nanohexagons.
Synthesis of ZnWO4 nanorods with [100] orientation and enhanced photocatalytic properties

Rui Shi,Yajun Wang,Di Li,Jing Xu,Yongfa Zhu

DOI: https://doi.org/10.1016/j.apcatb.2010.07.027

2010-01-01

Abstract:ZnWO4 photocatalysts with various morphologies were synthesized by a template-free hydrothermal synthesis process. The morphologies had a significant influence on the photocatalytic activity for methylene blue and Rhodamine B degradation. ZnWO4 nanorods with a highly [100] preferred orientation, obtained at pH 10, exhibited the highest photocatalytic activity among all the samples. This kind of nanorods had the most planes along the [100] direction—(010) and (011) planes, which meant most (010) and (011) planes exposed in ZnWO4 phase. Basis on the analysis of crystal plane and hydrogen-related defects, the (010) and (011) planes could speculate to be more active for photodegradation.
Improved Electrochromic Performance of WO3 Films with Size Controlled Nanorods

Guangzhong Yuan,Chenzheng Hua,Shahid Khan,Shanshan Jiang,Zhizheng Wu,Yong Liu,Jianxun Wang,Chenlu Song,Gaorong Han

DOI: https://doi.org/10.1016/j.electacta.2017.10.193

IF: 6.6

2018-01-01

Electrochimica Acta

Abstract:Electrochromic WO3 films with size controlled nanorods were successfully fabricated by a wet chemistry method. The structure and electrochromic properties of tungsten oxide nanorods and films were studied by High resolution transmission electron microscope, Scanning electron microscope, X-ray photoelectron spectroscopy, X-ray diffraction, and electrochemical methods. The average length and diameter of the monodispersed tungsten oxide nanorods increase from 38 x 3.2 nm to 89 x 4.5 nm with help from surfactants. The results show that the electrochromic response time of WO3 nanorod films are strongly dependent on the size of the nanorods. By simply changing the size of the nanorods, the response time of the nanorod films can be regulated nearly by about five times. The electrochemical impedance spectroscopy study showed that such trend can be attributed to the size effect of WO3 nanorods upon the dynamics of H ions diffusion. At the same time, all the nanorod films showed good electrochemical stability as there were no significant performance declines after 1000 cycles. The electrochromic modulations of transmittance at 633 nm were around 22%-49%. The above stated results demonstrate that, by controlling the size of WO3 nanorods, the electrochromic properties can be easily adjusted, especially the response time, indicating potential values for different response time required at different occasions. (c) 2017 Elsevier Ltd. All rights reserved.
Morphology-controlled Synthesis of CdWO_4 Nanocrystals

Gaorong Han

2013-01-01

Abstract:CdWO4 nanoparticles,nanorods,nanobundles,and nanowires were controllably synthesized via a hydrothermal method without any templates and surfactants using CdCl2,CdC2O4,CdCO3,(C6H5O7) 2Cd3,and Na2WO4 as raw materials.The as-prepared powders were characterized by XRD,TEM,HRTEM,and SAED.The results showed that the molar ratio of [WO42-]/[Cd2 +],reaction time,and the type of precursors had a crucial effect on the morphology and size of the products.
Synthesis of [100] Wurtzite InN Nanowires and [011] Zinc-Blende InN Nanorods

Nie Chao,Zhang Rong,Xie Zi-Li,Xiu Xiang-Qiang,Liu Bin,Fu De-Yi,Liu Qi-Jia,Han Ping,Gu Shu-Lin,Shi Yi,Zheng You-Dou

DOI: https://doi.org/10.1088/0256-307x/25/5/070

2008-01-01

Abstract:One-dimensional wurtzite InN nanowires and zincblende InN nanorods are prepared by chemical vapour deposition (CVD) method on natural cleavage plane (110) of GaAs. The growth direction of InN nanowires is [100], with wurtzite structure. The stable crystal structure of InN is wurtzite (w-InN), zincblende structure (z-InN) is only reported for 2D InN crystals before. However, in this work, the zincblende InN nanorods [011] are synthesized and characterized. The SEM and TEM images show that every nanorod shapes a conical tip, which can be explained by the anisotropy of growth process and the theory of Ehrlich-Schwoebel barrier.
Synthesis and Characterization of Highly Faceted (zn,cd)o Nanorods with Nonhexagonal Cross Sections

Yefeng Yang,Yinzhu Zhang,Yizheng Jin,Zhizhen Ye,Jianguo Lu,Haiping He,Jingyun Huang,Liping Zhu,Binghui Zhao

DOI: https://doi.org/10.1021/cg801323c

IF: 4.01

2009-01-01

Crystal Growth & Design

Abstract:Quasi-aligned (Zn,Cd)O nanorods with highly faceted morphology were synthesized by a simple catalyst-free thermal evaporation method. The crystal structure and optical properties of the as-synthesized nanorods were thoroughly investigated.-The results indicate that the (Zn,Cd)O nanorods are single crystals of wurtzite structure, having 12 side planes, namely, {01 (1) over bar0} and {11 (2) over bar0} planes. The presence of Cd is essential for obtaining these highly faceted nanorods. Room-temperature photoluminescence measurements indicated that the green emission of the products was attributed to both the surface-related defects and oxygen vacancies. These highly faceted nanorods possess significantly large surface-to-volume ratios and would be applicable in the fields of surface chemistry, photonics, and catalysis.
Growth of Epitaxial Tungsten Nanorods

Marcel Gillet,Romain Delamare,Eveline Gillet

DOI: https://doi.org/10.48550/arXiv.cond-mat/0506533

2005-06-21

Materials Science

Abstract:A simple vapour deposition technique was used to prepare WO3 one-dimensional nanostructures.WO3 is sublimated at a relatively low temperature (550 1C) in air at atmospheric pressure.The sublimated species are condensed on mica substrate at 500 1C.Single crystalline nanorods are grown in epitaxy on the mica surface with a growth axis along [0 1 0] directions and (0 0 1) plane parallel to the substrate.A growth process is proposed in which the formation of a onedimensional tetragonal tungsten bronze as precursor is the determining factor.
Synthesis of Single Crystal BaWO4 Nanowires in Catanionic Reverse Micelles.

Hongtao Shi,Limin Qi,Jianzhong Ma,Humin Cheng

DOI: https://doi.org/10.1039/b204995c

IF: 4.9

2002-01-01

Chemical Communications

Abstract:High aspect-ratio, single crystal BaWO4 nanowires with diameters as small as 3.5 nm and lengths up to more than 50 microns were synthesized in catanionic reverse micelles formed by an equimolar mixture of two surfactants: undecylic acid and decylamine.
Novel synthesis of hexagonal WO3 nanostructures

P. I. Gouma,K. Kalyanasundaram

DOI: https://doi.org/10.1007/s10853-015-8918-z

IF: 4.5

2015-02-24

Journal of Materials Science

Abstract:This paper discusses the synthesis and characterization of a new form of WO3 nanostructures based on the hexagonal WO3 (h-WO3) polymorph. This typically “metastable” phase was synthesized from a substoichiometric metal alkoxide precursor-tungsten (V) isopropoxide, by a novel colloidal synthesis method. Nanowires of h-WO3 were obtained upon heat-treating the sol–gel precursor at 400 °C. Further processing at elevated temperatures (515 °C) resulted in coarsening of the nanowires and the formation of nanowire bundles with polytypic character. Hexagonal WO3 differs from the other tungsten oxide polymorphs in that it possesses unique structural features such as long, hexagonal prism channels parallel to the c-axis and layered oxygen octahedra. This makes it a very attractive host matrix for metal ion intercalation for rechargeable batteries and for the selective gas sensing of amines.

materials science, multidisciplinary
Crystalline WO3 Nanowires Synthesized by Templating Method

KK Zhu,HY He,SH Xie,X Zhang,WZ Zhou,SL Jin,B Yue

DOI: https://doi.org/10.1016/s0009-2614(03)01206-5

IF: 2.719

2003-01-01

Chemical Physics Letters

Abstract:A new method is developed to obtain crystalline nanowires of WO3 using mesoporous silica SBA-15 as template. The method includes aminosilylation of the surface silanols within SBA-15 channels, anchoring of the heteropoly acid (HPA) to the grafted amine groups, thermal decomposition of the HPA, and removal of the silica framework with HF. The formation of the crystalline nanowires is monitored by the in situ XRD technique. TEM images intuitively confirm that the nanowires are uniform in diameter and HRTEM images further indicate that each nanowire belongs to single crystal although the growth orientations of these nanowires are different.
In situ Synthesis of Nano-WO3 Particles Attached to Sphere like Micro-WO3 Using Jagged CNTs as Template

Yin Yanhong,Tong Zhen,Xing Kangqian,Wu Ziping,Li Yesheng,Liu Xianbin,Liang Tongxiang,Liao Chunfa,Jiang Longke,Shao Jianfeng

2019-01-01

Rare Metal Materials and Engineering

Abstract:The CNT bundles can be jagged and used as a template to load the precursor H2WO4. The H2WO4 seeds can be enclosed by the jagged CNT template during liquid precipitation. The H2WO4 clusters with an average size of 500 nm consist of nanosized H2WO4 with 10 similar to 20 nm in diameter, which display a high specific surface area of 85.24 m(2).g(-1) and a total pore volume of 0.2933 m(3).g(-1). After thermal treating of H2WO4/CNTs under an oxygen atmosphere, nano-WO3 particles attached to the sphere-like micro-WO3 can be easily obtained by removing the CNT template. Its specific surface area and total pore volume are 18.7 m(2).g(-1) and 0.2055 m(3).g(-1) respectively. These results indicate that the jagged CNTs can play an important role for effective mediating WO3 with a hierarchical size, and exhibit excellent prospects for preparing micro-nanostructured materials.
Synthesis and Characterization of Quasi-Aligned Zncdo Nanorods

FZ Wang,ZZ Ye,DW Ma,LP Zhu,F Zhuge,HP He

DOI: https://doi.org/10.1063/1.2076434

IF: 4

2005-01-01

Applied Physics Letters

Abstract:Quasi-aligned ZnCdO single-crystal nanorods were prepared for the first time by using thermal evaporation of Zn and CdCl2 on a Si substrate with the presence of Au catalyst. The maximum Cd content was up to about 16.7at.%, which was significantly larger than the thermodynamic solid solubility limits. The ZnCdO nanorods have uniform flat hexagonal crystallographic planes with diameters of about 150nm. Notably, with the Cd content increasing, the ultraviolet near-band-edge emission was redshifted to 407nm(3.04eV) from 386nm(3.21eV). The direct modulation of the band gap caused by Cd substitution is responsible for the redshift. The possible growth mechanism of the ZnCdO nanorods was discussed.
Characterization and Modeling of WO 3 Nanowires Synthesized via the Solvothermal Method: A Proposed 8-Pointed Star Prism Structure

Chenjing Gao,Xingwu Guo,Xuan Wu,Li-Ming Peng,Juan Chen

DOI: https://doi.org/10.1021/acs.cgd.3c00182

IF: 4.01

2023-05-15

Crystal Growth & Design

Abstract:The solvothermal method is a popular approach for preparing multifunctional WO3 films. In this study, a WO3 film composed of nanowires with diameters of 40–50 nm and lengths of 400 nm to 1 μm was prepared on indium–tin oxide (ITO) glass via the solvothermal process. Transmission electron microscopy (TEM) analysis confirmed that each WO3 nanowire is a monoclinic single crystal with a [002]-selective growth direction. By analyzing the scanning electron micrography (SEM) images at ultrahigh magnifications and observing that the fast Fourier transform (FFT) images of all nanowires were identical, an 8-pointed star prism model was proposed for the morphology of WO3 nanowires. Based on this model, the exposed crystal planes on the outer surface of each WO3 single crystal are supposed to be {120} and {210}, thereby forming an 8-pointed star prism. Finally, the model was validated through focused ion beam (FIB) and TEM assessments. This study deepens our understanding of the morphology of solvothermally synthesized WO3 nanowires and may open up a window for future research on the subject.

chemistry, multidisciplinary,materials science,crystallography
Synthesis and Raman spectroscopic study of W20O58 nanowires

Jian Chen,Dongyu Lu,Weihong Zhang,Fangyan Xie,Jun Zhou,Li Gong,Xiao Liu,Shaozhi Deng,Ningsheng Xu

DOI: https://doi.org/10.1088/0022-3727/41/11/115305

2008-01-01

Abstract:Crystalline W20O58 nanowires were grown on silicon substrates by thermal evaporation of tungsten powders in a flow of argon gas without using any catalyst. Scanning electron microscopy shows that typical nanowires vary from 30 to 100 nm in diameter and around 8 mu m in length. X-ray diffraction and high-resolution transmission electron microscopy with electron diffraction study reveal that the nanostructures are crystalline. The laser power effect on the structure change of W20O58 nanowires has also been studied, which shows that W20O58 can be directly oxidized to WO3 very easily only by laser heating.
Hexagonal WO3·0.33H2O Hierarchical Microstructure with Efficient Photocatalytic Degradation Activity

Wei Li,Tingting Wang,Dongdong Huang,Chan Zheng,Yuekun Lai,Xueqing Xiao,Shuguang Cai,Wenzhe Chen

DOI: https://doi.org/10.3390/catal11040496

IF: 3.9

2021-04-14

Catalysts

Abstract:Structural design and morphological control of semiconductors is considered to be one of the most effective ways to improve their photocatalytic degradation properties. In the present work, a hexagonal WO3·0.33H2O hierarchical microstructure (HWHMS) composed of nanorods was successfully prepared by the hydrothermal method. The morphology of the HWHMS was confirmed by field-emission scanning electron microscopy, and X-ray diffraction, Raman spectroscopy, and thermogravimetric analysis demonstrated that the synthesized product was orthorhombic WO3·0.33H2O. Owing to the unique hierarchical microstructure, the HWHMS showed larger Brunauer–Emmett–Teller (BET) surface and narrower bandgap (1.53 eV) than the isolated WO3·0.33H2O nanorods. Furthermore, the HWHMS showed enhanced photocatalytic activity for degradation of methylene blue under visible-light irradiation compared with the isolated nanorods, which can be ascribed to the narrower bandgap, larger BET specific surface area, and orthorhombic phase structure of the HWHMS. This work provides a potential protocol for construction of tungsten trioxide counterparts and materials similar to tungsten trioxide for application in gas sensors, photocatalysts, electrochromic devices, field-emission devices, and solar-energy devices.

chemistry, physical
Three‐Dimensional Tungsten Oxide Nanowire Networks

J Zhou,Y Ding,SZ Deng,L Gong,NS Xu,ZL Wang

DOI: https://doi.org/10.1002/adma.200500885

IF: 29.4

2005-01-01

Advanced Materials

Abstract:Large-scale, single-crystalline, cubic-structured tungsten oxide (WO3-delta) nanowire networks (see Figure) have been synthesized by the thermal evaporation of tungsten metal powder in the presence of oxygen. The formation of ordered planar oxygen vacancies is suggested to be the driving mechanism for the formation of these interpenetrative nanowire networks.

Hexagonal Single Crystal Growth of Wo3 Nanorods along A [110] Axis with Enhanced Adsorption Capacity

One-dimensional Sub-stoichiometric W3O8Nanowires Filled Carbon Nanotubes

Novel route to WOx nanorods and WS2 nanotubes from WS2 inorganic fullerenes.

Novel Route to WO<i><sub>x</sub></i>Nanorods and WS<sub>2</sub>Nanotubes from WS<sub>2</sub>Inorganic Fullerenes

Controllable synthesis of hexagonal WO<sub>3</sub> nanorod-cluster films with high electrochromic performance in NIR range

An “edge to Edge” Jigsaw-Puzzle Two-Dimensional Vapor-Phase Transport Growth of High-Quality Large-Area Wurtzite-Type ZnO (0001) Nanohexagons

Synthesis of ZnWO4 nanorods with [100] orientation and enhanced photocatalytic properties

Improved Electrochromic Performance of WO3 Films with Size Controlled Nanorods

Morphology-controlled Synthesis of CdWO_4 Nanocrystals

Synthesis of [100] Wurtzite InN Nanowires and [011] Zinc-Blende InN Nanorods

Synthesis and Characterization of Highly Faceted (zn,cd)o Nanorods with Nonhexagonal Cross Sections

Growth of Epitaxial Tungsten Nanorods

Synthesis of Single Crystal BaWO4 Nanowires in Catanionic Reverse Micelles.

Novel synthesis of hexagonal WO3 nanostructures

Crystalline WO3 Nanowires Synthesized by Templating Method

In situ Synthesis of Nano-WO3 Particles Attached to Sphere like Micro-WO3 Using Jagged CNTs as Template

Synthesis and Characterization of Quasi-Aligned Zncdo Nanorods

Characterization and Modeling of WO 3 Nanowires Synthesized via the Solvothermal Method: A Proposed 8-Pointed Star Prism Structure

Synthesis and Raman spectroscopic study of W<sub>20</sub>O<sub>58</sub> nanowires

Hexagonal WO3·0.33H2O Hierarchical Microstructure with Efficient Photocatalytic Degradation Activity

Three‐Dimensional Tungsten Oxide Nanowire Networks