Abstract:Copper as well as copper base composites reinforced with coated and uncoated 1 wt% diamond, graphite particles or short carbon fibers are prepared by powder metallurgy process. The reinforcement particles were encapsulated with silver as well as copper layer by using the electroless deposition technique to investigate the influence of the reinforcement surface coating on the microstructure, density, electrical and thermal properties of the sintered samples. The coated and the uncoated powders were cold compacted at 600 MPa, and then sintered at 1173 K (900°C) for 2 h under hydrogen atmosphere. The phase composition, morphology and microstructure of the prepared powders as well as the copper base sintered composites were investigated using X-ray diffraction analysis (XRD) and Scanning Electron Microscope (SEM) equipped with an Energy Dispersive Spectrometer (EDS) respectively. The density of the sintered composites was measured by Archimedes method. The copper base consolidated composites had a density up to 96% and the reinforcement coated particles were distributed uniformly within the copper matrix better than the uncoated one. The electrical resistivity at room temperature and the heat transfer conduction of the produced samples were measured in a temperature range between 323 K (50°C) and 393 K (120°C). The results observed that the sintered materials prepared from the coated powder have lower electrical resistivity than the sintered materials prepared from the mixed powders. On the other hand the thermal conductivity values were calculated using the heat transfer conduction values by means of the Fourier formula. The results observed that the thermal conductivity of copper is (391 W/m·K), 1 wt% diamond/Cu is (408 W/m·K), 1 wt% graphite coated silver/Cu is (393 W/m·K), 1 wt% Cu coated short carbon fiber/Cu is (393 W/m·K), graphite/Cu is (383 W/m·K) and short carbon fiber/Cu is (382 W/m·K). The obtained composites are expected to be suitable for heat sink applications. The heat transfer testing experiments were done. The forced convection of the present work was done and compared with the previous work in the literature, and satisfactory agreement was achieved.

Thermal Properties of Cu Matrix Composite Containing Β-Eucryptite Particle

Structure and Thermal Expansion of Cu-90 vol. % Graphite Composites

Fabrication, mechanical and thermal properties of tungsten-copper coated graphite flakes reinforced copper matrix composites

Thermal and Electrical Properties of Feni/Cu Composites

Fabrication, Microstructure, Thermal and Electrical Properties of Copper Heat Sink Composites

Microstructure and thermal properties of copper matrix composites reinforced by 3D carbon fiber networks

Microstructure evolution and properties of Cu–Ag microcomposites with different Ag content

Microstructure and Properties of W Cu Composites with Low Copper Content at Different Sintering Temperatures

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Thermal Conductive and Dielectric Properties of Epoxy Resin with Bimetal Filler of Zn–Cu Particle

Evaluation of tribo-mechanical measurements and thermal expansion of Cu-based nanocomposites reinforced by high strength hybrid ceramics

Ionic Liquid-Modified Copper for the Enhanced Thermal Conductivity and Mechanical Properties of Epoxy Resin/Expanded Graphite Composites

Effects of Zr-Cu Alloy Powder on Microstructure and Properties of Cu Matrix Composite with Highly-Aligned Flake Graphite

Effect of titanium and zirconium carbide interphases on the thermal conductivity and interfacial heat transfers in copper/diamond composite materials

Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

A numerical study of the effect of interfacial thermal resistance on thermal conductivity of Cu-B/diamond composites

Microstructure and Thermal Property of W/cu Multilayer Composites

Thermal Properties of Copper Matrix-Ceramic Filler Composite Prepared by Polymer Solution Method

Synergistic enhancing effect of tungsten-copper coated graphite flakes and aluminum nitride nanoparticles on microstructure, mechanical and thermal properties of copper matrix composites

Effect of sintering temperature on microstructure and properties of nano-WC particle reinforced copper matrix composites prepared by hot-pressing sintering

High thermal and mechanical properties of carbon fiber network reinforced copper matrix composites achieved by configuration design and interface engineering