Abstract:We conducted a study to investigate the impact of the laser direct metal deposition (LMD) process on the microstructure, mechanical properties, temperature fields, and stress fields of 24CrNiMo steel in order to determine the optimal process parameters. The optimal parameters were determined to be a laser power of 1400 W, scanning speed of 7 mm/s, and powder feed rate of 8 g/min. When these optimal parameters were used, the formed specimens exhibited a high densely of up to 97.5 %. The microstructure of the specimens formed different parameters primarily consisted of bainite, martensite and ferrite. The specimens formed under various process conditions demonstrated good toughness, with a maximum tensile strength of 1131±20 MPa and an elongation of 16±1.8 %. Additionally, there was little difference in wear resistance and wear morphology among the specimens formed under different processes. The predominant wear mechanisms include abrasive wear, adhesive wearand oxidative wear. Increasing laser power and decreasing scanning speed resulted in a gradual increase in the temperature gradient gradually, leading to higher residual stresses in the formed specimens. Longitudinal stresses concentrated on both sides of the deposited layer, while the transverse stresses concentrated on one side of the deposited layer. The simulation results of the temperature field and stress field were consistent with the experimental results, with errors within the range of 10 %–20 %. This study demonstrated that the simulated models of temperature and stress fields effectively captured the fundamental phenomena in the LMD process, providing valuable tools for predicting and optimizing temperature distribution and stress in the LMD process. These findings contribute to the understanding and enhancement of the LMD process for 24CrNiMo steel, making it applicable for various applications requiring superior microstructure and mechanical properties.

Experimental Study on the Laser Rapid Forming Repairing of 45 Steel and 2cr12 Components

Microstructural evolution and mechanical properties of laser repaired 12Cr12Mo stainless steel

Investigation on repairing 30CrMnSiNi2A steel with laser additive and subtractive hybrid remanufacturing technology

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Fundamental Aspects on Laser Rapid & Flexible Manufacturing of Metallic Components

Evaluating the effect of repair using direct laser metal deposition on the fracture resistance of the cracked 1.2714 tool steel component

Laser-assisted robotic roller forming of an ultrahigh strength martensitic steel

Microstructures and mechanical properties of Ti6Al4V alloy repaired by the technology of point-mode forging and laser repairing

Effect of Ultrasonic‐Assisted Treatment on Microstructure and Mechanical Properties of Laser Deposition Repairing AlSi7Mg Alloy

Effect of laser direct metal deposition process on the microstructure and mechanical properties and temperature and stress fields of 24CrNiMo

Physical Simulation of Mold Steels Repaired by Laser Beam Fusion Deposition

Enhanced strength-ductility synergy in stainless steel 316L through hierarchically tailored microstructure via laser-based repair deposition

Impact of Ultrasonic Surface Rolling Processes on Microstructures and Fatigue Properties of 300M Steel Laser-Cladding-Repaired Components

Study on laser surface hardening process of 30CrMnSiNi2A ultra-high strength steel fabricated by laser deposition manufacturing

Aging Hardening Behavior and P Texture Formation of Laser Repaired GH4169 Nickel-Based Alloy

A thermo-metallurgical-mechanical model for microstructure evolution in laser-assisted robotic roller forming of ultrahigh strength martensitic steel

Laser Rapid Manufacturing of Special Pattern Inco 718 Nickel Based Alloy Component

Evolution of microstructure and mechanical properties of SUS430/C11000/SUS430 composites during the laser-forming process

Reconstruction Mechanism of Surface Integrity for Laser Additive Manufactured 316 L Stainless Steel Subjected to Ultrasonic Surface Rolling Process: Numerical Simulation and Experimental Verification

Experimental and Theoretical Investigation of Laser Pretreatment on Strengthening the Heterojunction Between Carbon Fiber Reinforced Plastic and Aluminum Alloy.

Study on Microstructure and Properties of LZ50 Axle Steel Repaired by Laser Additive Remanufacturing