Abstract:The work aims to study microstructure and surface quality of microcrystalline diamond film (MCD film) and NCD film (nanocrystalline diamond film), as well as cutting performance of MCD and NCD coated spade drills made from MCD and NCD films in cutting carbon fiber reinforced plastics (CFRP). The method of HFCVD was used to deposit MCD and NCD films on the surface of cemented carbide spade drills. Scanning electron microscope (SEM) was applied to observe surface and cross-sectional morphology of as-deposited diamond films, white-light interferometry was adopted to measure surface ·114· 表面技术 2018 年 8 月 roughness of the films, Raman spectroscopy was used to assess structural components of the films, X-ray diffractometer (XRD) was used to characterize crystal structure and crystal orientation of the films, and cutting experiment was performed to investigate cutting performance of uncoated tool as well as as-deposited MCD and NCD coated tool. The two kinds of films were evenly coated with diamond grains on the tool, both films were 8 μm thick, and crystal orientations were mainly in direction (111) and (220). The diamond grains of MCD film displayed pyramid structures with sharp edges and corners, the average grain size was about 2~3 μm. MCD film contained angular grains, and average grain size was 2~3 μm; and NCD film had a smoother surface, and average grain size was about 100 nm. Surface roughness value Ra of the MCD and NCD films in measured areas was 0.4 μm and 0.24 μm, respectively. Under the same cutting conditions, the uncoated tool reached rejection standardand could not be used any more after drilling 30 holes. After drilling 50 holes, MCD and NCD coated tools sustained the maximum abrasion loss of 0.192 mm and 0.093 mm, respectively on the flank, and none of them exceeded dullness standard VB=0.2 mm (width of flank wear land). The NCD coated tool exhibited the best wear resistance.The MCD and NCD films, especially NCD film, can effectively improve wear resistance of carbide cutting tools and extend service lives of the tools.

Comparative studies on the cutting performance of CVD diamond and DLC coated inserts in turning GFRP composite materials

Study on tribological behavior and cutting performance of CVD diamond and DLC films on Co-cemented tungsten carbide substrates

Comparative Studies on the Cutting Performance of HFCVD Diamond and DLC Coated WC-Co Milling Tools in Dry Machining Al/SiC-MMC

Study on the Fabrication and Cutting Performance of Hfcvd Diamond Coated Silicon Nitride Inserts

Fabrication and Cutting Performance of CVD Diamond Coated Inserts with Different Coating Thickness in Dry Turning Aluminum Alloy

Study on Fabrication and Cutting Performance of CVD Diamond Coated Drills in Machining the Carbon Fiber Reinforced Plastics

Fabrication and Drilling Tests of Chemical Vapor Deposition Diamond Coated Drills in Machining Carbon Fiber Reinforced Plastics

Deposition of Smooth Diamond Films with High Adhesive Strength on WC-Co Inserts and Their Cutting Performance in Turning GFRP

The Cutting Performance of Ultra-Smooth Composite Diamond Coated Wc-Co Inserts in Dry Turning Al/Sic-Mmc

FABRICATION OF DLC COATED COBALT-CEMENTED TUNGSTEN CARBIDE MICRO-DRILLS AND THEIR CUTTING PERFORMANCE

Deposition and Tribological Properties of Cvd Diamond/Diamond-Like Carbon Composite Films

Friction and Cutting Properties of Hot-Filament Chemical Vapor Deposition Micro- and Fine-Grained Diamond Coated Silicon Nitride Inserts

Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings

Study on tribology and cutting performance of boron doped diamond composite coated tool

Fabrication and application of CVD diamond coated cutting tools

Combined Influences of Tool Shape and As-Deposited Diamond Film on Cutting Performance of Drills for CFRP Machining

Study on the Cutting Performance of Hfcvd Diamond Coated Silicon Nitride Inserts in Dry Turning Aluminum Silicon Alloy

Fabrication and Cutting Performance of Micro- and Nano-crystalline Diamond Coated Spade Drills

Effect of boron and silicon doping on improving the cutting performance of CVD diamond coated cutting tools in machining CFRP

Comparative Study on the Tribological Performance of HFCVD Diamond and DLC Films under Water Lubricating Condition

Preparation and Cutting Performance of Ultra-Smooth CVD Composite Diamond Coated Ladder-Shape Drilling Tools