Abstract:Great progress has been carried out on the Micro Total Analysis System (μTAS) in recent years, in which the chemical analysis system is miniaturized by micromachining. This system can reduce reagent consumption, dispersion effects and analysis time. Nowadays, μTAS devices are beginning to make significant contributions to biotechnology, biomedicine and drug discovery. Meanwhile, due to the difficulties of controlling fluid motion in such a small scale, fluid flow driven in microfluidic devices has received increasing attention. So far electroosmotic flow (EOF) is one of the most popular and important fluid driven techniques in microfluidic devices because in an EOF the velocity profile is plug-like and the mean velocity is independent of the cross-sectional area, as well as its valveless control of fluid flow. Therefore, electro-osmotic flow can offer significantly less deleterious dispersive effects than pressure-driven flow and provide a favored high-performance sample separation technique. Due to its importance, electroosmotic flow in microchannels has received considerable attentions recently and been investigated both numerically and experimentally. However, fluid flow in microfluidic devices is often through channels with changes in cross-sectional area, and/or channels with bends and bifurcations, which make a great difference to velocity profile, pressure distribution and so on. A systematic study of these different configurations will provide valuable insight into the flow physics. The goal of the present study is to undertake a numerical study of EOF in microchannels with a sudden expansion in order to identify the factors affecting the flow. The present work is in the use of an incompressible lattice-Boltzmann model with a forcing term which is perhaps better suited to microflows than the conventional Navier-Stokes solvers. The impact of expansion ratio (ER), ionic molar concentration (c ∞), external electric potential and zeta potential on the flows are investigated. Numerical results including velocity profile, pressure distribution and external electrical potential distribution have been presented. It has been shown that boundary layer separation has been suppressed by the electroosmotic force exerted on the fluid near walls. Moreover, a sudden change in the channel has a great influence on the electroosmotic flows. A jump has been found in fluid velocity, pressure drop at the junction, as well as electrical potential due to EDL. The external electrical potential is linear along the axis of the channel but a turning point emerges at the junction. Non-linear pressure drop in the narrow channel becomes more obvious as ER increases. Results also show that velocity profile at the outlet depends on ER and c ∞. The convex velocity profile turns to concave one as ER or c ∞ increases, resulted from interactions between adverse pressure gradient and electric force exerted on the fluid in the middle of channel.

SEPARATION EFFICIENCY OF MICROPARTICLE IN THE DIVERGENT ELECTROKINETIC MICROCHANNEL FLOW

LATTICE BOLTZMANN SIMULATION OF ELECTROOSMOTIC FLOWS IN MICROCHANNEL WITH A SUDDEN EXPANSION

RESEARCH ON DIFFUSION IN MICRO-CHANNEL FLOW DRIVEN BY ELECTROOSMOSIS

Dielectrophoretic Choking Phenomenon of a Deformable Particle in a Converging‐diverging Microchannel

Numerical studies of the influence of particles' size distribution characteristics on the gravity separation performance of Liquid-solid Fluidized Bed Separator

Electrokinetic Particle Entry into Microchannels

Numerical Simulation And Research On The Electroosmotic Flow In The Curve Channel

Comparison of Micro- and Nano-Size Particle Transport and Depositions in 90 Degree Bend Microchannel

Design and Optimization of a Microfluidic Cell Separator Based on Dielectrophoresis

Simulation of the electro-osmosis in the micro-channel on the electrophoresis chip based on the theory of low Reynolds Number

Design Andoptimization Ofamicrofluidic CellSeparator Basedon Dielectrophoresi S

Simulation of particulate matter movement characteristics in multiphase flow field system

Efficient Microfluidic Particle Separation Using Inertial Pre-Focusing and Pre-Separation Structures Without Sheath Flow

A New Micromixer with Helical Microchannel and Research on Its Numerical Flow Field

A Complete Design Flow of Dielectrophoretic Chip

Micromixing Simulation of Novel Large-Double-Blade Impeller

Deformation and Approaching of Droplet Pair in a Microchannel under AC Electric Fields

Mixing Efficiency Analysis On Droplet Formation Process In Microchannels By Numerical Methods

Study on Liquid–Liquid Droplet Flow Separation in a T-Shaped Microseparator

Numerical simulation of bubble dynamics in a micro-channel under a nonuniform electric field.

Dielectrophoretic Effect on Droplet Dynamic Behaviors in Microchannels