Abstract:Gas turbine combustors design nowadays is aimed at achieving extremely lower NOx emissions through involving more air into the combustor to perform lean combustion, which results in the reduction of cooling air ratio for the liner walls. In this context, effusion cooling, one of the most effective cooling strategies, is adopted on the liner for its advantages of providing well cooling protection with limited amount of air. The swirl flow structure generated by the injector to stabilize flame in most modern lean-burn combustor is very complex with recirculation and vortex breakdown. So the interaction between three dimensional main flow and jets issued from the effusion holes is significant when assessing effusion cooling performance on the liner. In the present work, detailed effusion cooling feature on both inner and outer liners of a scaled annular combustor equipped with three axial swirlers has been provided under non-reactive and reactive conditions. The main flow is electrically heated for the non-reactive condition, while premixed combustion is realized after methane is fueled into the injectors and mixed with the air in the surrounding passage for the reactive condition. Temperature distribution on the target bended plate with 7 rows of discrete cooling holes in an in-line layout is captured by infrared thermography, and the cooling effectiveness is then analyzed. Effects of coolant to mainstream flow rate ratio and equivalence ratio are evaluated respectively. Results show that the macro rotational flow generated by the swirl flows interacts with cooling film and leads to non-symmetric cooling protection circumferentially on both liners. Additionally, averaged cooling effectiveness is found to increase with the flow rate ratio. At reactive conditions, stagnation of the high temperature swirl flow impinging on the liner wall locates at X/D range of 0.4–0.5, which has not been observed at non-reactive conditions. Also cooling effectiveness results indicate that outer liner obtains better cooling protection than inner liner when reaction is activated. Finally, the effect of most interested parameter for combustion process equivalence ratio is surveyed at Φ=0.7, 0.8 and 0.9. With experimental results, the importance of the combustion is highlighted in weighing the effusion cooling performance on the real annular combustor liners, which can’t be predicted comprehensively by non-reactive investigations. To obtain more knowledge of this issue, future work concerned with the flow field and flame visualization needs to be done through experimental techniques and numerical methods.

Experimental study on falling-film micro-combustor

Experimental Investigation on Thermal and Combustion Performance of a Combustor with Microchannel Cooling

Numerical Simulation for Combustion of Droplet with Volume of Fluid Formulation

Evaporating Interface In A Capillary Tube With High Heat Flux Induced By Micro Diffusion Flame

Experimental Study On Characteristics Of Falling Liquid Film Along The Surface Of Centrifugal Water-Film Reactor

Investigation on a Novel Type of Tubular Flame Burner with Multi-stage Partially-Premixing Features for Liquid-Fueled Gas Turbine

New method of experimental study on supercritical characteristic of single droplet fuel

Development and performace evaluation of a combustor with silicon carbide microchannel cooling

Experimental Study On Overall Cooling Effectiveness Of Swirl-Stabilized Model Combustor With Effusion Cooling

Experimental Study on the Aerodynamic and Separating Characteristics of a Novel Tiny‐oil Ignition Cyclone Burner for Down‐fired Utility Boiler

Experimental Investigation of Effusion Cooling Performance on the Liner of A Scaled Three Injector Annular Combustor

Experimental Study on Gas-Solid Two-Phase Flow Characteristics of a Vertical Cyclone Combustor System

Experimental and numerical study on heat transfer characteristics of tangential effusion cooling for a combustor liner

Combustion performances of a novel micro-combustor with a backward facing step and an exhaust gas recirculation channel

Improvement of Micro-Combustion Stability Through Electrical Heating

Emission Characteristics And Axial Flame Temperature Distribution Of A Circumferential Reverse Flow Combustor

Numerical and Experimental Assessment of a Novel Multinozzle Burner with CO2 Diluent to Improve the Emissions from a Swirling Flame in a Combustion Chamber

Combustion Instability and Emission Characteristics of Spray Flame under Flue Gas Jet

Experimental research on falling film flow and heat transfer characteristics outside the vertical tube

Experimental Study on Spray Characteristics of Air-Blast Atomizer Unit and Optimized Injector in Low Emission Combustor of Gas Turbine

Fuel modification flash boiling atomization and combustion in reciprocating engines