Abstract:The phenomenon of natural convection and thermal radiation heat transfer in fluid-saturated high temperature packed beds has been widely studied due to its various applications ranging from solar collectors to high temperature gas cooled reactor. With the local thermal non-equilibrium model, the majority of the numerical simulation studies on natural convection and radiation heat transfer in fluid-saturated porous media have limits. In these studies the internal heat transfer coefficients have always been calculated as the existing formulas, which were obtained by the experiments of forced convection in porous media [1-2]. However, natural convection heat transfer in porous media is dominated by the temperature difference between solid particles and fluid, which is different with the forced convection in porous media. For thermal radiation in porous media, the Rosseland diffusion approximation model has always been used in simulations by researchers [3-4], in which the mean absorption coefficient are not calculated according to the experiments and need to be determined by ray-tracing Monte Carlo simulations. Based on high temperature packed pebble beds, this study is aimed to compare the volume-averaged simulations and pore-scale simulations of high temperature packed beds, and predict the effective thermal conductivities of packed beds with temperature up to 1600°C. The effective thermal conductivities of the pebble beds under different temperatures are essential parameters in simulation models to analyze the maximum fuel temperature and temperature distribution in the reactor core in the reactor safety analysis. The SANA test facility was installed at the Research Centre, Julich in Germany specifically to investigate the heat transport mechanisms inside the core of a high temperature gas cooled reactor (HTGR). The validation of the volume-averaged approach and pore-scale approach are based on the experimental data of SANA test [5]. In high temperature helium-saturated annular packed pebble bed, the inner wall has a heat source and the outer wall is isothermally cooled at a lower temperature. The top and bottom walls are kept adiabatic. In the volume-averaged simulations, local thermal nonequilibrium model with the revised internal heat transfer coefficients and radiative heat flux is applied as the energy equation, and no uniform porosity distribution is used. To describe the random packed structure, PFC 3D software is used to simulate the spheres packing, which is used for direct pore-scale numerical simulations. Natural convection and thermal radiation in a 2D circular cross section of the annular pebble bed have been carried out. The effective thermal conductivities and temperature distributions of volume-averaged and pore-scale simulations of the high temperature helium-saturated annular packed pebble bed are corresponded well with the existed experimental data with temperature below 1000°C, and predict the effective thermal conductivities of the pebble bed core with temperature up to 1600°C, which are vital references for thermal hydraulic designs of high temperature gas cooled reactor core. INTRODUCTION Packed beds are widely used in variety of industries, such as catalytic reactors, absorption towers, packed bed regenerators and high temperature gas-cooled reactors. The heat transfer in an enclosure with high temperature packed beds have been gaining interest, because exploring the coupled mechanism of conduction, natural convection and thermal radiation in high temperature packed bed enclosures aids in improving the design of many applications. There are two main approaches for the CFD simulation of the geometry of the closely packed beds: the volume-averaged approach and the pore-scale approach. In the volume-averaged approach, an averaged concept of porosity is applied to simulate the closely packed geometry. As the internal heat transfer between solid particles and fluid is small because of natural convection in the enclosure, the temperature difference between solid and fluid cannot be ignored. So the local thermal non-equilibrium model is quite necessary for high temperature packed beds in an enclosure. Reda [6] has carried out the experimental investigation of a finite vertical cylinder with a heat source at the inner and constant temperature at the outer. The results showed that the radial temperature drop across the annulus was found to systematically depart from the finite-length cylinder as heat power was increased. Rajamani et al [7] have studied the natural convective heat transfer in an annular cylinder embedded with porous medium and discussed

Variant Porosity Pebble Bed Reactor Core Thermal Hydraulic Simulation

Investigation of the Flow and Temperature Uniformity in the Reactor Core of HTGR

Porous Structure Analysis of Large Scale Randomly Packed Pebble Bed in High Temperature Gas Cooled Reactor

A Thermal Resistance Model of Conduction–thermal Radiation Heat Transfer in Pebble-Bed Nuclear Reactors

Computational Fluid Dynamics Investigation of Thermal-Hydraulic Characteristics in a Simplified Pebbled Bed Modular Reactor Core Using Different Arrangements of Fuel Elements

Investigating the advantages and disadvantages of realistic approach and porous approach for closely packed pebbles in CFD simulation

Comparison of Volume-Average Simulation and Pore-Scale Simulation of Thermal Radiation and Natural Convection in High Temperature Packed Beds

Numerical Study of the Particle-Scale Heat Transfer in the HTR-PM Pebble Bed Based on GPU-DEM

Prediction of Flow and Temperature Distributions in a High Flux Research Reactor Using the Porous Media Approach

Numerical Simulation of the Coolant Flow and Heat Transfer Characteristics in the Reactor Core of Pebble Bed HTGR

Research on Fuel Pebble Modeling Methods Comparison and Eigenvalue Analysis of the Running-in Phase of HTR-PM

Numerical Methods and Simulation for Pebble Flows

Research on Influence of Different Simulation Methods of Bypass Flow in Thermal Hydraulic Analysis on Temperature Distribution in HTR-10

CFD Investigation of Thermal-Hydraulic Characteristics in a PBR Core Using Different Contact Treatments Between Pebbles

Effects of the Central Graphite Column Dimension and Pebble Size on Power Density Distribution in Annular Core Pebble‐bed HTR

Comparison of Several Thermal Conductivity Constants for Thermal Hydraulic Calculation of Pebble Bed Reactor

Porous Structure Analysis of the Packed Beds in A High-Temperature Reactor Pebble Bed Modules Heat Transfer Test Facility

Investigation of Flow and Heat Transfer in the Pebble Bed of the High Temperature Gas-cooled Reactor

DEM simulation of pebble flow in HTR 10 core by phenomenological method

Prediction and Analysis of Decay Heat Transfer in the Core of the Pebble Bed Reactor

Direct Numerical Simulation of the Flow Through a Randomly Packed Pebble Bed