Abstract:The demands of cost‐driven industrial applications can be satisfied by manufacturing composites with a low volume fraction of carbon fibres as phenolic carbon fibre‐reinforced composites and C/C composites, both with acceptable performances, for low‐ or high‐temperature applications, respectively. Polymeric composites reinforced with a low volume fraction (7.5% v/v) of carbon fibres were fabricated using laboratory‐produced phenolic resins, novolac (N) and resole (R), as matrices after different curing/post‐curing temperature profiles. By optimising the manufacturing conditions, the N‐based polymeric composites exhibited higher flexural strength, whereas the R‐based composites showed higher shear strength. C/C composites, namely N‐based and R‐based, were manufactured by pyrolysis of the previous polymeric composites up to 1000 °C. The pyrolysed composites were then densified by impregnation with an appropriate resin solution, followed by curing and new pyrolysis, and particularly by employing 1 up to 4 consecutive cycles of 'impregnation‐curing / pyrolysis'. Weight changes resulting from the impregnation‐curing and pyrolysis stages were determined. The curing of both resins was verified by FTIR. The apparent density and X‐ray diffraction data of the C/C composites were used to calculate their total percent porosities. The morphology and elemental analyses of C/C composites at their failure region (after flexural testing) were examined by SEM/EDS analyses. In comparison to N‐based C/C composites, R‐based ones exhibited: higher shear strength, lower flexural strength, higher Shore D hardness, slightly higher surface conductivity, and lower volume conductivity. The optimum conditions for the manufacture of C/C composites were achieved by applying two consecutive cycles of 'pyrolysis‐impregnation‐pyrolysis' to the polymeric composites. This article is protected by copyright. All rights reserved.

Preparation for 2D–C/C composites with pure RL textures and its characteristic

The carbon cloth reinforced 2D-C/C composites with phenolics as matrix precursor

Preparation of C/C Composites by Thermal Gradient Chemical Vapor Infiltration with Vaporized Kerosene As a Precursor

EFFECT OF C/C POROUS PREFORM ON THE MICROSTRUCTURE AND FLEXURAL STRENGTH OF C/C-SiC COMPOSITES

Effects of Carbon Fiber Architecture on the Microstructure and Mechanical Property of C/C-SiC Composites

Improvement of Film Boiling Chemical Vapor Infiltration Process for Fabrication of Large Size C/C Composite

Effect of Pyrocarbon Content in C/C Preforms on Microstructure and Mechanical Properties of the C/C–SiC Composites

Mechanical Properties Investigation of Carbon/carbon Composites Fabricated by a Fast Densification Process

Densification Behavior and Performances of C/C Composites Derived from Various Carbon Matrix Precursors

THE EFFECT OF DENSIFICATION ON FRICTIONAL PROPERTIES OF C/C COMPOSITES

Preparation, microstructure and properties of three-dimensional carbon/carbon composites withhigh thermal conductivity

Micro- and nano-structural investigations of C/C composites

Improvement of Chemical Liquid Vaporized Infiltration Process for Fast Densification of Carbon/Carbon Composites

Effect of chemical vapor infiltration on the flexural properties of C/C-SiC composites prepared by the precursor infiltration pyrolysis method

Performance Of Novolac Resin And Resole Resin‐Based Carbon/Carbon Composites In Relation To Their Fabrication Conditions

Rapid Fabrication of C/C-Sic Composites

Study of Rapid Fabrication and Microstructure of C/C-SiC Composites

Improvement of the mechanical properties of two-dimensional carbon/carbon composites

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration