Abstract:Due to the advantages of low cost, easy fabrication, mechanical flexibility, the research on organic solar cells has attracted a lot of attentions in the last decades. Among countless organic materials, the most successful ones are conjugated polymers, which were widely used in bulk heterojunction (BHJ) in conjugation with the fullerene [1]. In view of the fact the interpenetratedphase-separated p-n composites offer more chances for excitons to reach the p-n interfaces, BHJ greatly facilitates the dissociation of photogenerated excitons before decaying to ground state. During exciton dissociation process, the exciton delocalization at an ultra fast timescale has been observed recently, which has considerable effects on the charge generation and device performance. In this work, based on the recent studies [2–4], we established a theoretical model of polymer solar cells (PSCs) incorporating the exciton delocalization process. Through the model, we found the increase of delocalized excitons (compared to the total generated excitons) will significantly improve the short-circuit current, open-circuit voltage, fill factor and power conversion efficiency of PSCs. Particularly, the saturations of fill factor and open-circuit voltage are also observed, and the saturation points depend on the active layer thickness and recombination rate. For instance,the device model of 200nm thickness active layer has the saturated fill factor at 70% delocalization ratio, which is close to the conventional ratio of practical devices. The device configuration studied comprises a BHJ active layer sandwiched between a transparent anode and a metal cathode. Moreover, the active material is a mixture of OC 1 C 10 -PPV, as the donor, and PCBM, as the acceptor [5]. The generation rate of excitons is assumed to be homogeneous. The model proposed involves both the drift-diffusion model for photocarriers (Eq. (1)) and the diffusion and dissociation model for excitons (Eq. (2)). The governing equations are given as follows equation where q is elementary charge, n(p) is the electron (hole) density, and r G , r R are the parametersfor controlling exciton generation and bulk recombination, respectively. E is the internal E-field. µ and D are the mobility and diffusion coefficients. The exciton density is denoted by X diff and k diss is the exciton dissociation rate. The recombination R is taken to be a bimolecular form,with the rate given by Langevin [6], and η s is 0.25 for the singlet excitons. Using the physical parameters given by experiments [5], the nonlinear governing equation sets are solved self-consistently. The excitons are delocalized at an ultra fast timescale to form electron-hole pairs, which is much faster than the photo carrier relaxation time and exciton diffusion time. Consequently, the delocalization process was simulated by directly inserting the delocalization ratio η del into the equations.

Energy losing analyse of organic solar cells based on pentacene and C60

The Role Of Exciton Delocalization In The Performance Of Bulk-Heterojunction Polymer Solar Cells

Tackling Energy Loss for High-Efficiency Organic Solar Cells with Integrated Multiple Strategies.

Characterizing the Morphology and Efficiency of Organic Solar Cells by Multiscale Simulations

Study on the influence of embedded structure of carbon quantum dots of the organic solar cells with the territory active layer structure of P3HT: PC 61 BM: CQDs

Comparative performance analysis of poly (3-hexylthiophene-2, 5-dial) and [6, 6]-phenyl-C 61 butyric acid methyl ester-based organic solar cells in bulk-heterojunction and bilayer structure using SCAPS

Organic Photovoltaics Incorporating Electron Conducting Exciton Blocking Layers

Brief Introduction of Organic Molecules Solar Cell

Comparing the Device Physics, Dynamics and Morphology of Polymer Solar Cells Employing Conventional PCBM and Non-Fullerene Polymer Acceptor N2200

Effects on Photovoltaic Characteristics by Organic Bilayer- and Bulk-Heterojunctions: Energy Losses, Carrier Recombination and Generation

Reducing Energy Loss and Morphology Optimization Manipulated by Molecular Geometry Engineering for Hetero‐junction Organic Solar Cells

Computational characterization of organic photovoltaic devices

First-principles investigation of organic photovoltaic materials C$_{60}$, C$_{70}$, [C$_{60}$]PCBM, and bis-[C$_{60}$]PCBM using a many-body $G_0W_0$-Lanczos approach

Crystallographic Understanding of Photoelectric Properties for C60 Derivatives Applicable as Electron Transporting Materials in Perovskite Solar Cells

Deciphering the Effects of Molecular Dipole Moments on the Photovoltaic Performance of Organic Solar Cells

Enabling low voltage losses and high photocurrent in fullerene-free organic photovoltaics

Small-Molecular Organic Solar Cells with C-60/Al Composite Anode

10.4% Power Conversion Efficiency of Ito-Free Organic Photovoltaics Through Enhanced Light Trapping Configuration

Investigation of Various Active Layers for Their Performance on Organic Solar Cells

Quantifying Energy Losses in Planar Perovskite Solar Cells

Optimizing binding energy and electron-hole pair binding distance for efficient organic solar cells with low voltage loss