Abstract:High strength threaded fasteners are widely used in the aircraft industry, and service experience shows that for structures where shear loading of the joints is significant, like skin splices, fuselage joints or spar caps-web attachments, more cracks are initiated and grow from the edges of the fastener holes than from features like fillets radii and corners or from large access holes. The main causes of this cracking are the stress concentrations introduced by the fastener holes and by the threaded fasteners themselves, with the most common damage site being at the edge of the fastener holes. Intuitively, it is easy to visualize that after the crack initiation, during the growth stages, some of the load transferred initially by the fastener at the cracked hole will decrease, and it will be shed to the adjacent fasteners that will carry higher loads than in uncracked condition. Using currently available computer software, the method presented in this paper provides a relatively quick and quantitatively defined solution to account for the effects of crack length on the fastener loads transfer, and on the far field and bypass loads at each fastener adjacent to the crack. At each location, these variations are determined from the 3-dimensional distribution of stresses in the joint, and accounting for secondary bending effects and fastener tilt. Two cases of a typical skins lap splice with eight fasteners in a two rows configuration loaded in tension are presented and discussed, one representative for wing or fuselage skins configurations, and the second case representative for cost effective laboratory testing. Each case presents five cracking scenarios, with the cracks growing from approx. 0.03 inch to either the free edge, next hole or both simultaneously.

Crack Linkup And Residual Strength Of Multi-Hole Component

Reliability Analysis Of Unstiffined Aluminum Panels With Multiple Site Damage

Study on Measurement Method of Interior Stress Distributions in Engineering Rolled-Plates

Depth-sensing Indentation Measurement and Finite Element Analysis of Residual Stress Field Near Fatigue Crack Tip

Nonlinear Fracture Analysis of Delamination Crack Jumps in Laminated Composites

The Effect of Patch Geometry on the Static and Fatigue Behaviors of Defective Aluminum Panels Repaired with A Composite Patch

Component Structural Equivalent Research Based on Different Failure Strength Criterions and the Theory of Critical Distance

Residual stress effects on short crack propagation behavior in friction stir welded 7075-T6 aluminum alloy panel under biaxial loading: An experimental and numerical study

Effect of pitting corrosion on fatigue and crack growth behavior of both aluminum alloy 2024-t 62 and its panel

Ultimate strength of stiffened panels with a crack and pits under uni-axial longitudinal compression

Residual Strength of Metal Particulate Reinforced Ceramics with Parallel Cracks

Residual Strength Prediction of Aluminum Panels with Multiple Site Damage Using Artificial Neural Networks

Effect of Yield Strength Distribution Welded Joint on Crack Propagation Path and Crack Mechanical Tip Field

Effect of Pre-fatigue Damage on the Residual Strength of 2198-T8 Aluminum-Lithium Alloy Sheet with Holes

Application of a Cohesive Zone Model for Simulating Fatigue Crack Growth from Moderate to High <mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML" id="M1"><mml:mi mathvariant="normal">Δ</mml:mi><mml:mi>K</mml:mi></mml:math> Levels of Inconel 718

Analysis of weld root fatigue cracking in load-carrying high-strength aluminum alloy cruciform joints

The Effects of Fatigue Cracks on Fastener Loads during Cyclic Loading and on the Stresses Used for Crack Growth Analysis in Classical Linear Elastic Fracture Mechanics Approaches

Development and Evaluation of Methods of Plane Stress Fracture Analysis. Part 3. Application of the Residual Strength Prediction Technique to Complex Aircraft Structure

Cracks in the Laser Cladded Copper Alloy Coatings on Aluminum Alloy and Its Finite Element Analysis

Numerical simulation of distortion-induced fatigue crack growth using extended finite element method

Investigation on Fatigue Behaviour of Load-Carrying Fillet Welded Joints Based on Mix-Mode Crack Propagation Analysis