Abstract:The high temperatures and extended times involved with superplastic forming titanium mean that conventional die-steels are not suitable. Although dies manufactured from nickel-based alloys are used frequently, these are expensive, and more importantly, the coefficient of thermal expansion (CTE) of this materials are bigger than that of Ti–6Al–4V, which causes the dimensional inaccuracy between the dies and workpieces. The aim of this paper is to control the CTE of ZrO2–TiO2 ceramic die by adjusting the volume fraction of TiO2 and the relative density, and then controlling its’ CTE to be similar to Ti–6Al–4V alloy. In this paper, firstly, the relation between the expansion coefficient and the volume fraction of TiO2 and ceramic relative density was investigated. The results showed that with the increment of the volume fraction of TiO2, the expansion coefficient decreased. And with the rising of the relative density, the expansion coefficient increased. Secondly, based on the Turner Equation, a modified theoretical model was proposed in which the relative density of ceramic was considered. Using the model, the comparison was made between the experimental data and calculated data. The result showed that the linear CTE of ZrO2–TiO2 can be controlled by adjusting the volume fraction of TiO2 and corresponding relative density. Thirdly, to evaluate the practicability of the ZrO2–TiO2 ceramic die on superplastic forming, the ZrO2–TiO2 ceramic die (volume fraction of TiO2 is 27%, relative density is 93%) with the expansion coefficient (8.92×10−6°C−1) similar to Ti–6Al–4V was fabricated by sintering at 1520°C for 2h. The experiment of superplastically forming Ti–6Al–4V using ZrO2–TiO2 cylinder ceramic die was carried out, also. The Ti–6Al–4V cylinder shows better shape retention, surface quality and high dimensional accuracy, and the ceramic die seems adequate for superplastically forming the high accurate Ti–6Al–4V.

Preforming-die Design and Friction Changing to Control the Thickness Distribution of TC4 Deep Cylinder by Superplastic Forming

Tc4 Deep Cylinder with Uniform Thickness by Friction-Changing Direct-Reverse Superplastic Forming

Friction changing of direct-reverse superplastic forming to control the thickness distribution

Superplastic forming Ti-6Al-4V titanium alloy cylinder with near uniform thickness distribution

Investigation on the Factors Influencing the Thickness Distribution of Superplastic-Formed Components

Failure control on hydroforming process of thin-walled aluminum alloy with complex surface covers

Study on Controlling Thermal Expansion Coefficient of ZrO2–TiO2 Ceramic Die for Superplastic Blow-Forming High Accuracy Ti–6Al–4V Component

Effect of CoCrMo Die and Tool Surface Nano-Texture on Micro Backward Extrusion Formability of AA6063-T6

Effect of multi-point roller dies on the forming accuracy of profile in flexible 3D stretch bending technology

Preform Design and Microstructure-Property Analysis for Isothermal Extrusion of Complex Box-Shaped Components

Numerical Simulation on Shape Distortion of Superplastic Forming Ti-6Al-4V Cylinder

Die Design for Cylinder-shaped and Thin-walled Part

Plastic Deformation Mechanism in Double-Roller Clamping Spinning of Flanged Thin-Walled Cylinder

Superplastic Forming of Ti6Al4V Alloy Using ZrO2-TiO2 Ceramic Die with Adjustable Linear Thermal Expansion Coefficient

Numerical analysis of effect of material and processing parameters on thickness distribution during superplastic die bulging of cavity sensitive materials

Effect of discrete roller dies on the contour accuracy of profiles in multi-point flexible stretch-bending forming

Composite Die Design of Deep Drawing Flanging Trimming and Punching Bottom Hole

Casting Design Optimization Using Numerical Simulation of Precision Forging Die for Large Titanium Alloy Integral Bulkhead

An investigation on the friction in a micro sheet metal roll forming processes considering adhesion and ploughing

Superplastic Forming of a Three-Stage Hemispherical 5083 Aluminium Profile