Abstract:Improved mechanical properties of ferritic stainless steels (FSSs), such as toughness and high temperature or creep resistance, have been attained through the addition of stabilizing elements such as Nb and/or Ti. Therefore, stabilized ferritic stainless steels are good candidates to replace the conventional Cr-Ni austenitic stainless steels for specific applications to save the higher price of Ni. As compared to austenitic stainless steels, however, ferritic stainless steels possess lower formability which is closely depends on the gamma-fiber recrystallization texture. Hence, improvement of formability is desired for further wide applications of FSSs. The stabilizing effects of alloying elements work by consuming not only the interstitial atoms in solid solution but also forming the carbide and nitride precipitates such as TiC. TiN and NbC. The precipitation takes place in steel making processes such as slab reheating, hot rolling and coiling. The parameters involving these processes have their effects on the size, shape and distribution of the precipitates that influence the gamma-fiber recrystallization texture. Many papers intended to clarify the effect of precipitates. However, there were differences concerning the effect of precipitates, which may hinder further improvement of formability. In the present paper, precipitate size and dispersion were changed by controlling hot rolling processes and the effect of precipitate size and dispersion on the development of recrystallizaton texture in a 17%Cr ferritic stainless steels was investigated. Mechanical properties were measured by tensile tests. The characteristics of precipitate were observed by transmission electron microscopy, and X-ray diffraction was used to characterize texture evolution processes. The results show that low temperature finish rolling promotes the formation of a large number of fine and dispersed TiC precipitates in the hot band. After rolling and annealing, the state of fine and dispersed precipitation can be inherited in the cold rolled and annealed sheets. Strong gamma-fiber recrystallizaton texture is developed in the specimen with sparsely distributed and coarse precipitates. Fine and dispersed precipitates promote the nucleation of randomly oriented grains, strongly suppress the growth of recrystallized grain, and thereby weakening gamma-fiber recrystallizaton texture and impairing the formability of the cold rolled and annealed sheets. The precipitates have significant effects on the nucleation of randomly oriented grains and pinning grain boundary mobility during recrystallization annealing after cold rolling, which plays an important roles in controlling the gamma-fiber recrystallizaton texture in a ferritic stainless steels.

Strunture refinement of 12WT.%CR ferritic stainless steel by pulse current

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Overcoming the Trade-off Between Strength and Ductility in Austenitic Stainless Steel Using a High-Density Pulsed Electric Current

Textures and Precipitates in A 17%cr Ferritic Stainless Steels

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Regulating the dissolution of brittle nano-precipitated phase in FeCrAl alloy by pulse current to repair aging properties

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

Investigating the effect of Cr content on the microstructure and electrochemical measurement of low alloy steel

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Research status of welding technology of ferritic stainless steel

Study on Microstructure and Toughness of Welded Joint of 12%Cr Ferritic Stainless Steel

Study on ferritic stainless steel and its application on architecture structure

Microstructure, mechanical properties and deformation behavior of Cr-containing triplex low-density steels with different C content

MICROSTRUCTURAL REFINEMENT OF STRUCTURAL STEELS

Effect of microstructure variation on corrosion properties of as-cast 0Cr23Ni13 stainless steel at high strain rate of hot compression

Influence of Cr Content on the Mechanical, Oxidation, and Electrical Properties of Powder Metallurgy Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect

Evaluation of Intergranular Corrosion Susceptibility of 11cr Ferritic Stainless Steel by Dl-Epr Method

Effect of Cr on the phase transformation and interphase nanoprecipitation behaviours of high-strength microalloyed steels

Texture Development and Formability of Strip Cast 17% Cr Ferritic Stainless Steel

Maintaining Excellent Mechanical Properties via Additive Manufacturing of Low-N 25Cr-Type Duplex Stainless Steel

High ductility and corrosion resistance chromium gradient stainless steel for fuel cell bipolar plates fabricated via laser powder bed fusion