Abstract:Nowadays, the flow field at the compressor is more and more complex with the increasing of the aerodynamic loading. The complex flow in the endwall regions is thus key to aerodynamic blockage, loss production, and finally its performance deterioration. The design of Blended Blade and End Wall (BBEW) contouring technology had been proved to be useful in delaying, reducing, and eliminating the corner separation in the compressor. The BBEW technology can adjust the dihedral angle between the suction and the endwall in 30% of the spanwise easily, which is different with the fillet. However, the design of the BBEW always relies on the experiences of the designers, and the effective design results cannot be the optimal result. This paper presents an optimization design method for the BBEW technology, and analyses the flow mechanism of the BBEW design. Firstly, the parameters for the BBEW design is simplified as two, one is the maximum blended width, the other is the axial position of the maximum blended width. The optimal result can be obtained through the response surface method. Secondly, based on the optimization method, this paper make an optimization BBEW design at the suction side of a NACA65 linear compressor cascade with the turning angle 42 degrees. The numerical results show that the optimal BBEW design can eliminate the boundary layer separation at the corner intersection region, and reduce the suction side separation. When the incidence angle is 0 degrees, the BBEW technology can reduce the total pressure loss coefficient by 5%, and reduce the aerodynamic blockage coefficient by 14%. The aerodynamic performance of the cascade shows a more obvious improvement with the BBEW design at a larger incidence. The total pressure loss coefficient of the cascade is reduced by 20% at 15 degrees incidence. The numerical study shows that the design with the BBEW can control the axial development of the dihedral angle between the suction side and the endwall, which can eliminate the boundary layer separation at the corner intersection region. What’s more, the BBEW technology can produce a pressure gradient at the axial position of the maximum blended width, and value of the pressure gradient in proportion to the maximum blended width. This pressure gradient enhance the kinetic energy of the low energy fluid at the endwall region, which is consist of the secondary cross flow, thus elevating the capability to withstand the adverse pressure gradient, and improve the suction side separation around the trailing edge.

Numerical Study On End-Wall Flow In Highly Loaded Supercritical Compressor Cascades

Numerical Simulation of Effect of Blade End Slot on Performance of Compressor Cascade

Aerodynamic Design Method and Experimental Investigation of a High-Load Supersonic Compressor Cascade

Flow quality improvement of the wind tunnel testing for a highly-loaded compressor cascade at high incidence

Investigation of non-axisymmetric endwall contouring in a high loaded turbine stator cascade

Experimental and Numerical Investigation on the Aerodynamic Performance of a Compressor Cascade Using Blended Blade and End Wall

The Use of Blended Blade and End Wall in Compressor Cascade: Optimization Design and Flow Mechanism

An Investigation on Separation Configurations in Compressor Cascades with Boundary Layer Suction (BLS)

Numerical Studies on Application of Blended Blade and Endwall Technique on Transonic Centrifugal Compressor

Numerical and Experimental Study on Flow Loss Reduction Effect of Micro-Textured Surface on Compressor Cascade

Numerical Study of the Secondary Flow in Steam Turbine Static Cascade under Varying Conditions

Effect of Leakage Flow on the Endwall Cooling Performance in High Subsonic Turbine Cascade

Influence of Gap Shape on Flow Characteristics of Highly Loaded Compressor Tandem Cascades

Experiment and Numerical Simulation of the Performance on Scaled Compressor Cascade and Development of a Prediction Model

Investigation on corner stall prediction and flow control by blended blade and endwall technology in a compressor cascade based on modified Spalart-Allmaras model

Numerical investigation and loss estimation of high-pressure turbine cascade flow with contoured endwall and incoming wakes

Effects of moving endwall on the unsteadiness of tip leakage flow in compressor cascades

Investigation on corner stall prediction and flow control by blended blade and end wall technology in a compressor cascade based on modified Spalart-Allmaras model

Effect of end wall boundary layer suction on the performance of high load helium compressor cascade

The Endwall Effects of Stators with and Without Simplified Penny Gaps in a High-Loaded Multistage Compressor

The Effect of End Wall Boundary Layer on Matching and Corresponding Flow Control Technique for Multistage Axial Compressor