Abstract:Emissivity is an important parameter to characterize the thermophysical properties of materials. For non-conductive materials, high-temperature furnace heating or radiant heating is generally used in emissivity measurement. The problem in high-temperature furnace heating method is that tested materials may chemically react with the material of the heating container, thereby destroying the original characteristics of the materials. There will be problems of non-uniform heating of samples in the radiant heating method. The tested materials are usually heated unidirectionally and still in the radiant heating method, so there will be samples non-uniform distribution of sample temperature gradient. Based on laser rotating heating and sample/black body integrated design, this paper proposes a new method. The samples are spinning while measuring, measuring the emissivity of non-conductive materials at high temperature, and establishing a corresponding measurement model. This method break through the limitations of traditional measurement methods, in which the samples are still while measuring. The sample and black body are designed integrally, and the micro-area spectral radiation imaging method is adopted to measure the spectral radiation energy and temperature of the black reference body and the sample at the same time. The heat conduction equation under the laser rotating heating state is established, and the temperature distribution of typical sample materials is simulated. The results show that the temperature field distribution of the rotating sample is relatively uniform. The relationship between the temperature field distribution and the infrared spectral emissivity measurement error is analyzed. The lower limit of the material thermal conductivity applicable to this test method is shown. Based on this method, a corresponding measurement device was built to test the spectral emissivity of a typical material silicon carbide at 1 000 K. The spectral emissivity of each specific high-temperature point was tested at 4 mu m, and the silicon carbide material was measured at The characteristics of the spectral emissivity wavelength change and temperature change rule characteristics of the infrared band. The results are compared with the foreign measurement results, and the results are relatively consistent, which verifies the feasibility of the laser rotating heating spectral emissivity test method. The characteristics of the spectral emissivity wavelength change and temperature change rule characteristics of the silicon carbide material in the infrared band are obtained. The results are compared with the foreign measurement results, and the results are relatively consistent, which verifies the feasibility of the laser rotating heating spectral emissivity test method. With this method, the physical and chemical characteristics of the sample are not destroyed, the sample heats up quickly, the temperature field in the measurement area is uniform, the upper limit of the measurement temperature range is high, and the temperature unevenness caused by the laser static and unidirectional heating is reduced effectively. The sample's temperature and spectral radiation energy can be measured at the same time, so the standard high temperature black body does not need to be designed separately. This method solves the existing high-temperature non-uniform heating and radiant energy synchronous comparison measurement in non-conductive materials emissivity measurement. It can be applied to measure the high-temperature spectral emissivity of various non-conductive materials.

Mathematical Model of Strip Specimens for Application of Pulse-Heating Technique

Thermal conductivity measurement of phase-change material near melting point based on perturbation method

Measurement of High-Temperature Spectral Emissivity Using Integral Blackbody Approach

One-Dimensional Thermal Analysis of the Flexible Electronic Devices Integrated with Human Skin.

Method and Device for Measuring High-Temperature Spectral Emissivity of Non-Conductive Materials Based on Laser Rotation Heating

Numerical Modeling of the Performance of Thermoelectric Module with Polydimethylsiloxane Encapsulation

Simultaneous measurements of high-temperature total hemispherical emissivity and thermal conductivity using a steady-state calorimetric technique

Simultaneous thermal conductivity and specific heat measurements of thin samples by transient Joule self-heating

Numerical simulation of the thermal-mechanical process of high current pulsed electron beam treatment

Simultaneous measurement of normal spectral emissivity and temperature of materials with low thermal conductivity

An Analytic Model of Transient Heat Conduction for Bi-Layered Flexible Electronic Heaters by Symplectic Superposition

Numerical Approach for the Theory of Harmonic Self-Heating Technique to Measure Thermophysical Properties of Suspended Thin Samples

Mass Nature of Heat and Its Applications Iv: Thermal Wave and Periodic Temperature Oscillation in Metallic Films Heated by Ultra-Short Pulsed Lasers

High temperature imaging dynamic measurement techniques under harsh experimental environment

Simultaneous measurements of the specific heat and thermal conductivity of suspended thin samples by transient electrothermal method.

A Steady-State Measurement System for Total Hemispherical Emissivity

Structural Design of Dual-Type Thin-Film Thermopiles and Their Heat Flow Sensitivity Performance

Spectral Pyrometry for Practical Temperature Measurement in the TEM

Modeling Analysis and Experimental Study of a Temperature-difference Type Heat Flux Meter

Bio-Heat Model with Cooling of Surface Evaporation Radiated High Power Millimeter-Wave

Modeling and Analysis of Dynamic Heat Transfer Characterization of Environment Simulating Facility for High Temperature Gas-cooled Reactor