Abstract:Objective Prototype of a novel device, previously named "Dynamic Aortic Valve (DAV)", for left ventricular assistance was fabricated and tested to demonstrate its feasibility. Methods An impeller similar to an airscrew is to be placed in the position of aortic valve .The impeller is held by a cylindrical supporting cage locating in the lumen of arising aorta by attaching to the valve annulus via a sewing ring. A permanent magnetic rotor is fitted into the cage and fixed to the impeller to form a “rotor-impeller”. The supporting cage would port the aortic wall thus prevent the rotor from connecting to the wall, allowing the rotor to whirl freely. The alternating magnetic field generated by a extracorporeal device would drive the rotor to rotate and the axial flow of blood from ventricular to the aorta would be produced, resulting in the reduction of the ventricular load. Based on such hypotheses, A prototype of “DAV” was fabricated and tested in a mock circuit. In the present stage, The rotor is 8 mm in diameter and 15 mm in length, the impeller has 3 vanes with a diameter of 18 mm. The supporting cage is 22 mm in outer diameter and 20 mm in length. The alternating magnetic field turning the“"rotor-impeller” was produced by a rotating magnet placed side by side with the “rotor-impeller” at a distance of 15 mm.Result The prototype was fitted into a tube, simulating the aorta, full of water solution of glycerol. When actuated by magnetic force, the “rotor-impeller” of DAV started to rotate, producing a pressure difference and liquid flow in the tube. The flow rate or pressure difference proportioned to rotational speed. At the state of maximal output of hydraulic power, the flow rate reaches 5 L/min against a afterload of 6.65 kPa.Conclusion The maximal pressure differential maintained by the DAV prototype at 12 000 r/min is 10.64 kPa. The results demonstrated the feasibility of the concept of DAV, suggesting that further researches on this concept are justifiable.

Development of a Novel Axial Flow Ventricular Assist Device and its Preliminary Animal Experiment

DESIGN OF IMPLANTABLE AXIAL-FLOW BLOOD PUMP AND NUMERICAL STUDIES ON ITS PERFORMANCE

The simulation of multiphase flow field in ventricular assist device and analysis of hemolytic capability

Experimental Study of Domestic Emplantable Ventricular Assist Device

Hemolysis and Animal Experiments with the Magnetically Drived Axial Flow Ventricular Assist Device

Computational Fluid Dynamics-Based Hydraulic and Hemolytic Analyses of a Novel Left Ventricular Assist Blood Pump.

Design and Experimental Testing of a Heart Assist Device with Pulsatile Flow Pump

Evaluation of the Hemolysis and Fluid Dynamics of a Ventricular Assist Device under the Pulsatile Flow Condition

Experimental Study of Hemolysis in Vitro and Animal Testing for Fu Wai Axial Blood Pump

Design and numerical evaluation of an axial partial-assist blood pump for Chinese and other heart failure patients.

Digital Simulation to the Development of Axial Blood Pump for Artificial Heart

Design optimization of an axial blood pump with computational fluid dynamics.

Numerical and in Vitro Experimental Investigation of the Hemolytic Performance at the Off-Design Point of an Axial Ventricular Assist Pump

A hemodynamic and hemolysis study of the axial pump with hydrodynamic-magnetically levitated impeller in swine

HYDRAULICS AND IN VITRO HEMOLYSIS TEST OF A MAGLEV IMPLANTABLE VENTRICULAR ASSIST DEVICE

Applications of CFD Technique in the Design and Flow Analysis of Implantable Axial Flow Blood Pump

In Vivo Experimental Testing of the FW Axial Blood Pump for Left Ventricular Support in Fu Wai Hospital

In vitro testing of an intra-ventricular assist device.

Experimental Study on a New Device for Left Ventricular Assist: Dynamic Aortic Valve

Computational fluid dynamics analyses of a micro pediatric ventricular assist blood pump

Development of the Baylor/NASA axial flow ventricular assist device: in vitro performance and systematic hemolysis test results