Abstract:Objective: To investigate the amount of bone grafting, bone defect gap residual rates, and biomechanical stability of the injured vertebral body after reduction of thoracolumbar burst fractures, pedicle screw-rods fixation, and bone graft by bilateral pedicle or unilateral spinal canal. Methods: Eighteen fresh lumbar spine (L1-5) specimens of calves (aged 4-6 months) were collected to establish the burst fracture model at L3 and divided into 3 groups randomly. After reduction and fixation with pedicle screws, no bone graft was given in group A (n = 6), and bone graft was performed by bilateral pedicles in group B (n = 6) and by unilateral spinal canal in group C (n = 6). The amount of bone grafting in groups B and C was recorded. The general situation of bone defect gaps was observed by the DR films and CT scanning, and the defect gap residual rates of the injured vertebrae were calculated with counting of grids. The compression stiffness was measured by ElectreForce-3510 high precision biological material testing machines. Results: The amount of bone grafting was (4.58 +/- 0.66) g and (5.72 +/- 0.78) g in groups B and C respectively, showing signficant difference (t = 2.707, P = 0.022). DR films and CT scanning observation showed large bone defect gap was seen in injured vertebrae specimens of group A; however, the grafting bone grains was seen in the "eggshell" gap of the injured vertebral body, which were mainly located in the posterior part of the vertebral body, but insufficient filling of bone graft in the anterior part of the vertebral body in group B; better filling of the grafting bone grains was seen in injured vertebral body of group C, with uniform distribution. The bone defect gap residual rates were 52.0% +/- 5.5%, 39.7% +/- 2.5%, and 19.5% +/- 2.5% respectively in groups A, B, and C; group C was significantly lower than groups A and B (P < 0.05), and group B was significantly lower than group A (P < 0.05). Flexion compressive stiffness of group C was significantly higher than that of groups A and B (P < 0.05), but no significant difference was found between groups A and B (P > 0.05). Extension compressive stiffness in group C was significantly higher than that in group A (P < 0.05), but no significant difference was found between groups A and B, and between groups B and C (P > 0.05). The compression stiffness of left bending and right bending had no significant difference among 3 groups (P > 0.05). Conclusion: Thoracolumbar burst fracture pedicle screws fixation with bone grafting by unilateral spinal canal can implant more bone grains, has smaller bone defect gap residual rate, and better recovery of flexion compression stiffness than by bilateral pedicles.

Influence of cortical bone defects of different lengths on biomechanics of long tubular bone

Biomechanical changes in long tubular bone due to different cortical bone defects at tension/compression sides

[An Experimental Study on Biomechanical Effects Due to Unilateral Cortical Bone Defect in Long Tubular Bone].

Effect of screw holes on the biomechanics of long tubular bone

[Biomechanical Research on Upper Femur with Vertical and Bending Stress].

Differences in the mechanical behavior of cortical bone between compression and tension when subjected to progressive loading

Spatiotemporal Characterization of Microstructure Morphology, Mechanical Properties and Bone Remodeling of Rat Tibia Under Uniaxial Compressive Overload Loading

Characterization of damage mechanisms in cortical bone: Quantification of fracture resistance, critical strains, and crack tortuosity

Effect of Plate–Bone Distance and Working Length on 2.0-mm Locking Construct Stiffness and Plate Strain in a Diaphyseal Fracture Gap Model: A Biomechanical Study

A Biomechanical Investigation on the Incorporation of Cortical Allograft in Rabbit Ulna Defects

Mechanical response and in-situ deformation mechanism of cortical bone materials under combined compression and torsion loads

[Influence of two kinds of bone grafting methods on bone defect gap residual rates and compressive stiffness after reduction of thoracolumbar burst fracture]

[Experimental Study of Porous TCP to Generate Tissue-Engineered Long Bone].

A biomechanical study on the restoration of experimental bone defect of the femoral head

Evaluation of Damage to Trabecular Bone of the Osteoporotic Human Acetabulum at Small Strains Using Nonlinear Micro-Finite Element Analyses

A proposal for the combined analysis of bone quantity and quality of human cortical bone by quasi-brittle fracture mechanics

Crack propagation in cortical bone is affected by the characteristics of the cement line: a parameter study using an XFEM interface damage model

Biomechanical and finite element evaluation of model of canine radius segmental defect used in tissue engineering

A Controlled Variable Study of the Biomechanical Properties of the Proximal Femur before and after Cancellous Bone Removal

The biomechanical implications of lacunar and perilacunar microarchitecture on microdamage accumulation in cortical Bone

Diametral compression of non-circular diaphyseal bone sections