Abstract:Dislocation source-limited hardening and ductilization is an effective strategy to obtain superior strengthductility synergy in some engineering structural metals. Recent works demonstrated that the synergy could be enhanced by grain-size reduction. However, the mechanism of grain-size dependence is still a mystery. In this work, bulk pure Ni produced by electrodeposition and subsequent annealing, with grain sizes ranging from -20 nm to -20 pm, were methodically investigated to unravel the mechanism of the grain-size effect on dislocation source-limited hardening and ductilization. The high-density nano-twinning in the as-electrodeposited nanograined specimens exhibited better thermodynamic stability than the peers with random high-angle grain boundaries, leading to fine recrystallized grains with low-density dislocations. The low dislocation density enabled extra hardening beyond grain boundary strengthening via yield-point behavior with grain sizes ranging from -110 nm to -10 pm and extra ductilization over -500 nm. This work demonstrated that the prerequisite for dislocation source-limited hardening was that the dislocation density of the specimen should be lower than the size-dependent critical value of ((1.1 x 10 7 / d ) m -2 , d is the grain size in unit of the meter) where a transition from forestdominated hardening to dislocation source-limited hardening could occur. On the other hand, dislocation source-limited ductilization only worked when the grain size was comparable to/larger than the theoretical dislocation mean slip distance. Dislocation source-limited ductilization resulted from more room in grains for accumulation of dislocations and deformation nano-stacking faults enabling the higher work hardening rate. This work offered an altogether new avenue to obtain stronger and more ductile metallic materials through utilizing grain-size dependent dislocation source-limited hardening and ductilization.(c) 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

Grain Size Evolution of Nano-Micro-crystalline Materials Based on Dislocation Density Model

FEM Simulation of Micro-Crystalline Materials During ECAP Based on the Dislocation Evolution Method

Numerical Analysis of Nano- or Micro-Crystalline Materials During ECAP by Dislocation Evolution Method

Experimental and Numerical Investigation on Pure Aluminum by ECAP

Influence of Grain Size in the Near-Micrometre Regime on the Deformation Microstructure in Aluminium

Impact of Grain Size Distribution on the Multiscale Mechanical Behavior of Nanocrystalline Materials

Atomic Simulations of Grain Structures and Deformation Behaviors in Nanocrystalline CoCrFeNiMn High-Entropy Alloy

Grain size gradient effect on grain boundary mediated deformation of nano-grained metals

Modeling of the Plastic Deformation of Nanostructured Materials with Grain Size Gradient

The Influence of Grain Size and Temperature on the Mechanical Deformation of Nanocrystalline Materials: Molecular Dynamics Simulation

Grain size dependent microstructure and texture evolution during dynamic deformation of nanocrystalline face-centered cubic materials

Unravelling the Size‐Dependent Mechanical Properties of Nanocrystalline Face‐Centered‐Cubic Metals: from the Dislocation Point of View

Grain Size Effects on Plastic Strain and Dislocation Density Tensor Fields in Metal Polycrystals

Local Deformation Mechanisms in Metal Systems with a Tailored Grain Size Distribution

Grain size and orientation affected deformation inhomogeneity and local damage of hot-deformed Al-Zn-Mg alloy

Research on Grain Refinement of Aluminum Alloys

Grain-size effect on dislocation source-limited hardening and ductilization in bulk pure Ni

Effects of Grain Size and Shape on Mechanical Properties of Nanocrystalline Copper Investigated by Molecular Dynamics

Enhanced Ductility of Nanomaterials Through Cooperative Dislocation Emission from Cracks and Grain Boundaries

Effects of Precipitates Versus Solute Atoms on the Deformation-Induced Grain Refinement in an Al–Cu–Mg Alloy