Abstract:Modular bridge expansion joints (MBEJs) are commonly used in bridges and are often subjected to fatigue damages, which necessitate fatigue monitoring of MBEJs to ensure the reliable operation of the bridges. In this paper, a stress wave based active sensing approach using piezoceramic transducers is developed to monitor the fatigue damage of MBEJ. A MBEJ involves mainly center beam, edge beam, support bar, support box, sliding bearing, sliding spring, elastomeric strip seal, full-penetration weld and reinforcing plate. In practice, for a MBEJ, the part that is most prone to fatigue damage is the full-penetration weld between the center beam and the support bar. In this paper, a specimen, which is the full-scale center-beam/support-bar (CB/SB) assembly, was designed and fabricated to facilitate the experimental study. The assembly mainly includes center beam, support bar, reinforcing plate, and full-penetration weld. The lead zirconate titanate (PZT) transducer bonded on the support bar was used as the actuator and the PZT transducer mounted on the center beam was as the sensor. Dial indicators were utilized to measure the vertical displacement of the center beam. Two series of tests, including static test, and fatigue test, were performed on the specimen in an alternating fashion. Based on the number of cyclic loading, the experiment was divided into six different stages: 0th cycle (the healthy state), 0.8 million cycles, 1.6 million cycles, 2.4 million cycles, 3.2 million cycles, and 4 million cycles. The signals received by the PZT sensor were analyzed with the help of wavelet packet analysis. In addition, the structure stiffness also was considered as a comparative approach in this paper. Experimental results show that during the fatigue test, the structure stiffness decreases with the number of cycle loading. However, the method can only obtain the fatigue damage impact on the entire structure, and cannot determine the fatigue damage degree of a certain weld. On the other hand, the proposed method can accurately monitor the fatigue damage degree of full-penetration welds. The research results show that the developed piezoceramic enabled active sensing approach can monitor and estimate the fatigue damage in MBEJ in real-time.

Concrete Structure Monitoring Based on Built-in Piezoelectric Ceramic Transducers

Self-sensing Joints for In-Situ Structural Health Monitoring of Composite Pipes: A Piezoresistive Behavior-Based Method

Concrete Damage Diagnosis Using Electromechanical Impedance Technique

Piezoelectric sensor based nondestructive active monitoring of strength gain in concrete

Development And Application Of Structural Health Monitoring System Based On Piezoelectric Sensors

Crack Detection of FRP-Reinforced Concrete Beam Using Embedded Piezoceramic Smart Aggregates

Dynamic stress monitoring for RC beam using PMN-PT-based three-direction normal stress sensor

Damage detection for structural health monitoring using ultra-sensitive flexible piezoelectret sensors

Detection of Debonding Between Fiber Reinforced Polymer Bar and Concrete Structure Using Piezoceramic Transducers and Wavelet Packet Analysis

Time Reverse Modeling of Damage Detection in Underwater Concrete Beams Using Piezoelectric Intelligent Modules

PZT Based Piezoelectric Sensor for Structural Monitoring

Damage Detection of L-Shaped Concrete Filled Steel Tube (L-CFST) Columns under Cyclic Loading Using Embedded Piezoceramic Transducers

Experimental Research on Monitoring Concrete Expansion and Cracking Induced by Corrosion based on Distributed Optical Fiber Sensor

Monitoring Fatigue Damage of Modular Bridge Expansion Joints Using Piezoceramic Transducers

Monitoring the curing process of in-situ concrete with piezoelectric-based techniques – A practical application

Multiple Crack Detection of Concrete Structures Using Impedance-based Structural Health Monitoring Techniques

Non-destructive concrete strength evaluation using smart piezoelectric transducer—a comparative study

Real-Time Monitoring of Bond Slip between GFRP Bar and Concrete Structure Using Piezoceramic Transducer-Enabled Active Sensing

Piezoelectric Transducers for Structural Health Monitoring of Joint Structures in Cylinders: A Wave-Based Design Approach

Integrated Structural Health Assessment Using Piezoelectric Active Sensors