Abstract:Accumulation of electrostatic charges in gas–solid fluidized beds can lead to particle adhesions, electrostatic discharges, wall sheeting and even explosion. Therefore, it is of vital importance to reduce the electrostatic level in industrial fluidized beds. Adding chemical static agents was reported as one of the most promising ways to control fluidized bed electrostatic potentials. In this study, the electrostatic potential distributions were measured in a three-dimensional column gas–solid fluidized bed with the LLDPE particles for fluidization and the introduction of chemical static agents. Seven charge inducing agents including TiO2, Al2O3, MgO, H2O, C2H5OH, ZnO, and Fe2O3 were employed to investigate their influence on electrostatic potentials distribution respectively. Additionally, Al(Et)3, which is normally used as the cocatalyst for olefin polymerization, was also studied for comparison. It was found that the adding of negative charge inducing agent such as TiO2 made the positive electrostatic potentials shift to higher values and the negative electrostatic potentials shift to lower values. The injection of positive charge inducing agent such as Al2O3 and MgO caused the positive electrostatic potentials dropping to lower values and the negative electrostatic potentials shifting to the values near zero at low injection amount. Affecting mechanism of charge inducing agents was discussed based on the experimental results and the electronegativity of corresponding compounds. It was found that the electronegativity (χi) of the metal ion played an important role in determining the charge polarity on the LLDPE particles and the change in the electrostatic potentials after contact and separation with the charge inducing agent particles.

Bipolar Charging of Dielectric Powder and Electrostatic Potential Distribution in Gas-Solid Fluidized Beds

Electrostatic Potentials in Gas–solid Fluidized Beds Influenced by the Injection of Charge Inducing Agents

Electrostatic potential in gas-solids fluidized beds influenced by injection of charge inducing agents

Experimental Investigation of Electrostatic Effect on Particle Motions in Gas-Solid Fluidized Beds

Electrostatic Distribution in the Riser of the Multizone Circulating Fluidized Bed for Polypropylene

Online Measurement of Particle Charge Density in A Gas-Solid Bubbling Fluidized Bed Through Electrostatic and Pressure Sensing

Simultaneous Measurement of Electrostatic Charge and Its Effect on Particle Motions by Electrostatic Sensors Array in Gas-Solid Fluidized Beds

Experimental Investigation of Electrostatic Reduction in a Gas–Solid Fluidized Bed by an in Situ Corona Charge Eliminator

Experimental Investigation of Electrostatic Effect on Bubble Behaviors in Gas-Solid Fluidized Bed

Distribution of Electrostatic Potential in a Gas−Solid Fluidized Bed and Measurement of Bed Level

Electrostatic Effects on Hydrodynamics in the Riser of the Circulating Fluidized Bed for Polypropylene

Numerical simulation of gas-solids fluidized bed with applied electric field

Critical Comparison of Electrostatic Effects on Hydrodynamics and Heat Transfer in a Bubbling Fluidized Bed with a Central Jet

Effects of DC Electric Fields on Meso-Scale Structures in Electrostatic Gas-Solid Fluidized Beds

Cfd-Dem Investigation of Particle Elutriation with Electrostatic Effects in Gas-Solid Fluidized Beds

A Comparative Study of Electrostatic Current and Pressure Signals in a MSFC Gas–solid Fluidized Bed

Electrostatic Classification of Fine Powders

Characterization of Flow Pattern of Cohesive Particles in Gas-Solid Fluidized Bed Via Axial Distribution of Particle Motions

Experimental Investigation of Bubble and Particle Motion Behaviors in A Gas-Solid Fluidized Bed with Side Wall Liquid Spray

Effects of Agglomerates on Electrostatic Behaviors in Gas–solid Fluidized Beds

Electrostatic behavior with fines of different sizes added into gas-solid fluidized bed