Abstract:For development of thin bioactive coatings on metal implants, a dense and uniform apatite layer was coated onto titanium (Ti) implants in situ by using a new biomimetic method, which is composed of apatite nucleation and growth steps in simulated body fluid (SBF). Analysis of the coatings by thin film X-ray diffraction and scanning electron microscopy-energy dispersive X-ray microanalysis (SEM-EMPA) before implantation showed that its characteristics were very similar to those of natural bone. The coated and uncoated rectangular plates were bilaterally implanted into the tibial proximal metaphyses of rabbits. After 6, 10 and 25 weeks post-implantation, the bone bonding and bone formation at the bone-implant interfaces were evaluated by a detachment test and undecalcified histological examination. Mechanical testing in tension showed that the failure load of apatite layer-coated Ti implants was significantly higher than that of uncoated control at each time period (all P < 0.001). Histologically, it was shown that bone was deposited directly onto the apatite coating without any intervening soft tissue, while in the paired controls, interpositional soft tissue was seen at the bone-implant interface. By SEM-EPMA, a uniform calcium- and phosphorus-rich layer was detected between the coated implants and bone, but not in uncoated controls at either earlier or later time periods. The results indicate that the apatite layer deposited on Ti in situ may significantly increase the bone bonding strength by providing a bioactive surface, which allows for an early bone apposition to the implant. In addition, the apatite layer-coated Ti produced by the biomimetic process may fulfil the requirements of favourable thin coatings and strong adhesion at the metal-coating interface.

Formation of Bone-Like Apatite on Poly(l-Lactide) to Improve Osteoblast-Like Compatibility in Vitro and in Vivo

Cell Affinity of Bone-like Apatite Coating Modified Poly(L-lactide-co-glycolide)

Effect of Hydrolysis Pretreatment on the Formation of Bone-like Apatite on Poly(L-lactide) by Mineralization in Simulated Body Fluids

Air-plasma Treatment Promotes Bone-Like Nano-Hydroxylapatite Formation on Protein Films for Enhanced in Vivo Osteogenesis

Biological Efficacy of Modified Structure of Polymer Surfaces for Bone Substitute

The Effect of Oxygen Plasma Pretreatment and Incubation in Modified Simulated Body Fluids on the Formation of Bone-Like Apatite on Poly(lactide-Co-glycolide) (70/30)

Apatite Layer-Coated Titanium for Use As Bone Bonding Implants

Longer-Term Mechanical And Biological Evaluation Of Titanium Alloy Coated With Apatite Layer

Surface Processing Technology of Apatite Coating of on Bone Tissue Engineering Scaffolds of Poly (lactic Acid)

[Hydrolysis of Poly(l-Lactic Acid) Fibers and Formation of Low Crystalline Apatite on Their Surface by a Biomimetic Process].

Improved Cell Adhesion and Osteogenesis of Op-Ha/plga Composite by Poly(dopamine)-Assisted Immobilization of Collagen Mimetic Peptide and Osteogenic Growth Peptide

Apatite Formation Induced by Chitosan/Gelatin Hydrogel Coating Anchored on Poly(aryl ether nitrile ketone) Substrates to Promote Osteoblastic Differentiation

Biomimetic Mineralization of Poly(l-Lactic Acid) Nanofibrous Microspheres for Bone Regeneration

Biomimetic Poly(L-Lactic Acid) Scaffolds with Interconnected Macropores, Collagen-Like Nano-Scale Fibers, and Bone-Like Apatite

Bioinspired Modification of Poly(L-lactic Acid)/nano-Sized Β-Tricalcium Phosphate Composites with Gelatin/Hydroxyapatite Coating for Enhanced Osteointegration and Osteogenesis

Improvement of the Adhesion and Proliferation of Human Osteoblastic-Like Cells with Biomimetic Nanoapatite Coatings

Block copolymer of polyphosphoester and poly(L-lactic acid) modified surface for enhancing osteoblast adhesion, proliferation, and function.

In Vitro Growth of Bioactive Nanostructured Apatites Via Agar-Gelatin Hybrid Hydrogel.

Optimization of Poly(ε‐caprolactone) Surface Properties for Apatite Formation and Improved Osteogenic Stimulation

Bone-like apatite coating on functionalized poly(etheretherketone) surface via tailored silanization layers technique

Biomineralization of Bone-Like Hydroxyapatite to Upgrade the Mechanical and Osteoblastic Performances of Poly(lactic Acid) Scaffolds.