Abstract:In the present study, the creep rupture behaviour and microstructural evolution of 2195-T84 Al-Li alloy are investigated at different tensile stresses. It is found that as the applied stress during the creep rupture process increases, the corresponding creep strain and creep rate significantly increase. Moreover, the evolution of microstructures, including precipitates, dislocation density and creep cavities at different stages is characterized using a transmission electron microscope (TEM), X-ray diffractometer (XRD) and scanning electron microscopy (SEM). The main strengthening precipitates are identified as T-1 (Al2CuLi) and theta ' (Al2Cu) phases. Obtained results show that as the applied stress increases, T-1 and theta ' phases are gradually coarsened. This coarsening is more pronounced for theta ' phase. Furthermore, the creep cavities are mainly distributed at the interface between the insoluble second phase particles and the matrix, and their average sizes gradually increase as the applied stress increases. Meanwhile, the density and size of dimples on the fracture surface gradually decrease as the applied stress increases. Moreover, the main fracture mechanism changes from transgranular dimple fracture to quasi-cleavage fracture. Based on the microstructural evolution, a novel set of unified creep rupture constitutive model is proposed. The established model incorporates the evolution of microstructures, including the dislocation density, average length of T-1 and theta ' precipitates and creep cavitation, and correlates microstructural variables with creep rate. The results calculated by the constitutive model are in good agreement with the experimental data, which validates the proposed model.

Effects of Texture on Inner Pressure Creep Behaviors of Advanced Zirconium Alloys

Effect of Texture on Anisotropy of Creep Behavior of Advanced Zirconium Alloys

Unveiling the Microstructure Evolution and the Short-Time Tensile Creep Behavior in the CuCrZr Alloy

Influence of Thermal and Thermo-Mechanical Processing on the Creep Resistance of Mg-10Gd-3Y-0,4Zr Alloy

Creep Behaviours of Cr25Ni35Nb and Cr35Ni45Nb Alloys Predicted by Modified Theta Method

Study on the Effect of Micromorphology and Creep Properties of In Situ (ZrB2 + Al2O3)/AA6016 Composites in Extruded State

Effects of Tailoring Microstructure on Short-Term Creep Behavior of High Nb Containing TiAl Alloys under Various Stress Levels

Effect of zinc additions on the microstructure mechanical properties and creep behavior of as-cast Mg–3Sm–0.4Zr (wt.%) alloy

Effect of texture on the room temperature tensile and creep properties of Ti–6Al–4V plate with large thickness

Mechanical Properties and Creep Behavior of Mg-Gd-Y-Zr Alloys

Microstructural evolution of Mg–14Gd–0.4Zr alloy during compressive creep

Microstructure Evolution and Creep Behavior of High-Pressure Die-Cast Mg–9Al–1Zn–1Sr Alloy

Tensile Creep Behavior and Microstructure Evolution of Mg-11Gd-2Y-0.5Zr Alloy

Effect of Zinc Addition on Microstructure and Mechanical Properties of Mg–7Y–3Sm–0.5Zr Alloy

Creep Behavior of Mg–11Y–5Gd–2Zn–0.5Zr (wt.%) at 573 K

Investigating The Stress Level Impact On The Creep Rupture Behaviour Of 2195-T84 Al-Li Alloy: Experimental And Constitutive Modelling

Compressive creep behavior of extruded Mg-4Sm-2Yb-0.6Zn-0.4Zr alloy

Effect of Annealing Treatment on the Creep Behaviour of Zr-2.5Nb Alloy

Effect of Dynamic Precipitation on Creep Behavior of Mg-5zn-2al(-2y) Alloy

Polycrystalline Effects on Irradiation Creep and Growth in Textured Zirconium

Separate contributions of texture and grain size on the creep mechanisms in a fine-grained magnesium alloy