Abstract:The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated working conditions. However, the pump usually has to work in large-scale and time-variant working conditions. Therefore, the flow ripple characteristics of pump and analysis for its test accuracy with respect to variant steady-state conditions and transient conditions in a wide range of operating parameters are focused in this paper. First, a simulation model has been constructed, which takes the kinematics of oil film within friction pairs into account for higher accuracy. Afterwards, a test bed which adopts Secondary Source Method is built to verify the model. The simulation and tests results show that the angular position of the piston, corresponding to the position where the peak flow ripple is produced, varies with the different pressure. The pulsating amplitude and pulsation rate of flow ripple increase with the rise of pressure and the variation rate of pressure. For the pump working at a constant speed, the flow pulsation rate decreases dramatically with the increasing speed when the speed is less than 27.78% of the maximum speed, subsequently presents a small decrease tendency with the speed further increasing. With the rise of the variation rate of speed, the pulsating amplitude and pulsation rate of flow ripple increase. As the swash plate angle augments, the pulsating amplitude of flow ripple increases, nevertheless the flow pulsation rate decreases. In contrast with the effect of the variation of pressure, the test accuracy of flow ripple is more sensitive to the variation of speed. It makes the test accuracy above 96.20% available for the pulsating amplitude of pressure deviating within a range of ±6% from the mean pressure. However, with a variation of speed deviating within a range of ±2% from the mean speed, the attainable test accuracy of flow ripple is above 93.07%. The model constructed in this research proposes a method to determine the flow ripple characteristics of pump and its attainable test accuracy under the large-scale and time-variant working conditions. Meanwhile, a discussion about the variation of flow ripple and its obtainable test accuracy with the conditions of the pump working in wide operating ranges is given as well.

Influence of Fuel Pump Failure on the Fuel Feeding Stability of an Aircraft Fuel System

Flow characteristics simulation and low-noise design of fuel piston pump

Fault Diagnosis And Prevention Of Flow Sensor For Fuel Supply System

Influence of the Rotation Speed on the Internal Flow Characteristics of an Aircraft Fuel Gear Pump

An Investigation into the Swash Plate Vibration and Pressure Pulsation of Piston Pumps Based on Full Fluid-Structure Interactions

Investigation of cavitation characteristics in an aircraft centrifugal fuel pump

Analyses of Pressure Fluctuation and Fluctuation Reduction of an Automobile Fuel Pump

Analysis on Stability of Electron-Controlled Unit Pump System for Diesel Engine

Research on the Performance of a Centrifugal Aviation Fuel Pump Based on Response Surface Methodology

Impact of Typical Steady-State Conditions and Transient Conditions on Flow Ripple and Its Test Accuracy for Axial Piston Pump

Analysis of Cavitation Characteristics of High Temperature Fuel Piston Pump in the Process of Suction and Discharge

Modelling and Reducing Fuel Flow Pulsation of a Fuel-Metering System by Improving Response of the Pressure Control Valve During Pump Mode Switching in a Turbofan Engine

Effect of Structural Parameters on Output Characteristics of a Novel Self-Supplied Aviation Intelligent Pump

Investigation Into The Effects Of Index Angle On Fluidborne Noise And Structureborne Noise Of A Tandem Axial Piston Pump

Experimental and Numerical Studies on Erosion Damage in Damping Holes on the Valve Plate of an Axial Piston Pump

Numerical Simulation of the Transient Process of Power Failure in A Mixed Pump

Numerical Analysis of the Structural and Flow Rate Characteristics of the Fuel Injection Pump in a Marine Diesel Engine

Classification and Control of Key Factors Affecting the Failure of Aviation Piston Turbocharger Systems Using Model-Based System Safety Analysis

Effects of Fuel Temperature on Injection Performance of an EUP System

Aviation fuel pump health state assessment based on evidential reasoning and random forests

Fuel Flowrate Control for Aeroengine and Fuel Thermal Management for Airborne System of Aircraft—An Overview