Abstract:Despite the great advancement and wide use of titanium (Ti) and Ti-based alloys in different orthopedic implants, device-related infections remain the major complication in modern orthopedic and trauma surgery. Most of these infections are often caused by both poor antibacterial and osteoinductive properties of the implant surface. Here, we have demonstrated a facile two-step laser nanotexturing and immobilization of silver onto the titanium implants to improve both cellular integration and antibacterial properties of Ti surfaces. The required threshold laser processing power for effective nanotexturing and osseointegration was systematically determined by the level of osteoblast cells mineralized on the laser nanotextured Ti (LN–Ti) surfaces using a neodymium-doped yttrium aluminum garnet laser (Nd:YAG, wavelength of 1.06 μm). Laser processing powers above 24 W resulted in the formation of hierarchical nanoporous structures (average pore 190 nm) on the Ti surface with a 2.5-fold increase in osseointegration as compared to the pristine Ti surface. Immobilization of silver nanoparticles onto the LN–Ti surface was conducted by dip coating in an aqueous silver ionic solution and subsequently converted to silver nanoparticles (AgNPs) by using a low power laser-assisted photocatalytic reduction process. Structural and surface morphology analysis via XRD and SEM revealed a uniform distribution of Ag and the formation of an AgTi-alloy interface on the Ti surface. The antibacterial efficacy of the LN–Ti with laser immobilized silver (LN–Ti/LI–Ag) was tested against both Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria. The LN–Ti/LI–Ag surface was observed to have efficient and stable antimicrobial properties for over 6 days. In addition, it was found that the LN–Ti/LI–Ag maintained a cytocompatibility and bone cell mineralization property similar to the LN–Ti surface. The differential toxicity of the LN–Ti/LI–Ag between bacterial and cellular species qualifies this approach as a promising candidate for novel rapid surface modification of biomedical metal implants.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.langmuir.2c00008.Cytocompatibility assessment of LN/LI Ti, Rockwell hardness analysis, cytocompatibility analysis, antibacterial activity analysis of different laser processed surfaces, viability of E. coli after exposure to Ti and LN–Ti/LI–Ag surfaces, surface elemental weight percentage analysis, and examples of topographic surface modification on titanium for dual response antibacterial and promote osteogenesis (PDF)This article has not yet been cited by other publications.

Laser surface modification of titanium alloy used as biomaterial

Laser Surface Modification Of Titanium Alloys - A Review

Laser surface modification of Ti--6Al--4V: wear and corrosion characterization in simulated biofluid

Microstructure and Hardness of the Laser Surface Treated Titanium

Mechanical and Corrosion Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings

Improving the Bio-Tribological Properties of Ti6Al4V Alloy via Combined Treatment of Femtosecond Laser Nitriding and Texturing

Laser Cladding of Ti Alloys for Biomedical Applications

Elastic-plastic properties of titanium and its alloys modified by fibre laser surface nitriding for orthopaedic implant applications

Microstructure and Properties of Ti6Al4V Surface Processed by Continuous Wave Laser in Different Atmospheres

Influence of Laser Treatment of Ti6Al4V on the Behavior of Biological Cells

Process optimization and property of Ti-Al-Cr-Nb coating on titanium alloy surface by laser in-situ synthesis

The Interplay of Thermal Gradient and Laser Process Parameters on the Mechanical Properties, Geometrical and Microstructural Characteristics of Laser-Cladded Titanium (Ti6Al4V) Alloy Composite Coatings

Mechanical Properties and Residual Stress Measurements of Grade IV Titanium and Ti-6Al-4V and Ti-13Nb-13Zr Titanium Alloys after Laser Treatment

Laser-Assisted Nanotexturing and Silver Immobilization on Titanium Implant Surfaces to Enhance Bone Cell Mineralization and Antimicrobial Properties

Surface Modification of Ti3Al2.5V Titanium Alloy Using Laser Texturing With Improved Wettability, Corrosion and Bioactivity Behaviour

Surface Modification of Pure Ti by Laser Alloying with B and Ni Mixed Powders

Research Progress of Laser Cladding Coating on Titanium Alloy Surface

Progress in Laser Surface Modification Technology of Titanium Alloy

Effect of Laser Power on the Microstructure and Mechanical Properties of TiN/Ti 3 Al Composite Coatings on Ti6Al4V

Ultra-low wear of titanium alloy surface under lubricated conditions achieved by laser texturing and simultaneous nitriding

Enhanced Tribological Properties and Cyto-Biocompatibility of Dental Ti6Al4V Alloy Via Laser Surface Texturing