Abstract:Laser ultrasound (LU) is a contactless and couplant-free remote non-destructive (NDE) technique, which uses lasers for ultrasonic generation and detection rather than conventional piezoelectric transducers. For a transducer, an important characteristic is the directivity , the angle-dependent amplitude of the ultrasonic waves generated in the material. In the non-destructive thermoelastic regime, LU source has been widely modelled as a surface force dipole. However, the directivity of LU in more complex material, where there is an increasing demand for NDE, such as carbon fibre reinforced plastic (CFRP), is yet to be understood. In the current paper, a finite element (FE) modelling methodology to obtain the directivity of LU in complex material is presented. The method is applied to a conductive isotropic material (aluminium, Al) for validation against an existing analytical solution and then applied to a heterogeneous anisotropic material (carbon-fibre reinforced plastic, CFRP). To get the directivity of a specific wave mode, the signal for that mode needs to be resolved in time from other modes at all angles. This is challenging for shear (S) waves in a small model domain due to the head wave, so a technique for suppressing the head wave is shown. The multi-physics model solves for thermal expansion, which models the laser source as a surface heat flux for the Al case, and a buried heat source for the CFRP case, according to where the energy is deposited in the material. The same ultrasound generation pattern can be obtained by using a suitable pure elastodynamic loading, which is shown to be a surface force dipole as per the validation case for Al, and a buried quadrupole for the CFRP case. The modelled directivities are scaled and fitted to experimental measurements using maximum likelihood , and the goodness of fit is discussed. For the Al case, the S wave is preferred over the longitudinal (L) wave for inspection due to greater signal amplitude. For the CFRP case, the quasi-longitudinal (qL) wave in CFRP shows a maximum amplitude directly below the source, and has a greater amplitude than the quasi-shear (qS) wave, suggesting a better choice for inspection.

Thermoelastic Finite Element Modeling Of Laser Generation Ultrasound

Simulations Of Ultrasonic Waveform Excited By Pulsed Laser By Using Finite Element Method

Thermoviscoelastic Finite Element Modeling of Laser-Generated Ultrasound in Viscoelastic Plates

Numerical Simulation of Laser-Generated Lamb Wave by Finite Element Method in Thin Transversely Isotropic Laminate Composite

Mechanisms of Laser-Generated Ultrasound in Plates

Simulation of Laser-Generated Longitudinal and Shear Ultrasonic Waves in A Diamond Anvil Cell by the Finite Element Method

Numerical analysis of wave-type heat transfer propagating in a thin foil irradiated by short-pulsed laser

Finite Element Modeling of the Interaction of Laser-Generated Ultrasound with a Surface-Breaking Notch in an Elastic Plate

Finite Element Modeling Of Bulk Ultrasonic Waves Generated By Ring-Shaped Laser Illumination In A Diamond Anvil Cell

Molecular Dynamics Simulation Of Ultra-Fast Thermal Transition In Thin Foil Irradiated By High Power Ultra-Short Laser

Numerical Simulation of Laser Induced Ultrasonic in a Diamond Anvil Cell by Finite Element Method

A fractional dual-phase-lag generalized thermoelastic model of ultrashort pulse laser ablation with variable thermal material properties, vaporization and plasma shielding

Non-Fourier conduction model with thermal source term of ultra short high power pulsed laser ablation and temperature evolvement before melting

Extremum Imitation Study Of Thermoelastic Ultrasound Stress Pulse Generation By Laser Pulse

Transient thermoelastic response analysis of porous composite structures ablated by the ultrashort pulse laser considering absorption mechanisms of plasma plume

Finite element modelling strategy for determining directivity of thermoelastically generated laser ultrasound

Finite element analyses of temperature fields in moving solids irradiated by a laser source

Thermal Behavior of Thin Metal Films Irradiated by Shaped Femtosecond Pulse Sequences Laser

A generalized thermoelastic diffusion problem of thin plate heated by the ultrashort laser pulses with memory-dependent and spatial nonlocal effect

Transient Responses of Dielectrics During Ultrashort Pulsed Laser Irradiation Using a Generalized Thermoelastic Model Considering Temperature-Dependent Thermophysical Properties

Thermoelastic Wave in Metal Induced by Ultrafast Laser Pulses