Abstract:AbstractThe search for suitable friction materials for high-speed train is an attractive but difficult problem. In recent years, a variety of different novel friction materials were fabricated to meet the aims of high loads and speeds under ambient environment. Carbon fiber-reinforced carbon composites (C/C), carbon fiber-reinforced silicon carbide composites (C/C-SiC) and metallic composites fabricated by powder metallurgy are three excellent materials among them. Here a comparison of these three different materials working as brake pads, coupled with high-density C/C-SiC brake disk, was described. All the experiments were conducted using the same procedure with increasing initial braking speed (the rotation speed of brake disk at the beginning of braking process) from 30 to 59 m/s and constant load of 1.25 MPa, simulating the real working condition of high-speed train. The coefficient of friction (COF) and wear rates of three materials were compared and analyzed. During experiments, the COF of metallic and C/C pads remains nearly constant at 0.31 and 0.22, respectively, with increasing braking speed, while that of C/C-SiC exhibits a parabola. These different trends of COF may be attributed to the distinctive forming processes of friction film on the top of contact surfaces. Meanwhile, the wear rates of metallic composites increase rapidly from 683 to 1803 mm3/MJ with initial braking speed, while C/C-SiC presents the highest wear loss of 1887 mm3/MJ at 49 m/s and lowest value of 315 mm3/MJ at 59 m/s. Interestingly, the wear rate of C/C composites, due to the appropriate bonding strength of matrix/fiber and relatively high shear stress, decreases from 3698 to 903 mm3/MJ with increasing initial braking speed, which does not consist with pre-existing paper. Thus, metallic pads presented the lowest wear rates at lower speed (<49 m/s) but the highest at high speed, while C/C-SiC composite pads showed the greatest wear resistance at high speed. This investigation of three different friction materials will enhance our understanding of these friction materials and benefit the selection and safe application of high-speed train friction materials.

RESEARCH PROGRESS ON CARBON/SILICON CARBIDE FRICTION COMPOSITE

The Research on Friction and Wear Properties of Silicon Carbide and Silicon Nitride

Mechanical and tribological properties of C/C–SiC ceramic composites with different preforms

Fabrication and Process Optimization of Chinese Fir-Derived SiC Ceramic with High-Performance Friction Properties

Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

Research Progress on Microstructure Characterization of Silicon Carbide Fibers

Tribological behaviour of C/C–SiC composites—A review

Microstructures and properties of C/C–SiC composites derived from different gaseous carbon matrix precursors

Study on the Tribological Properties of Carbon Fabric/Polyimide Composites Filled with SiC Nanoparticles

Research and application prospect of short carbon fiber reinforced ceramic composites

Microstructure of C/SiC Braking Material

The structural effect of SiC form ceramic on the compressive strength and thermal expansion properties of Cu–SiC composites

Comparison of Friction and Wear Behavior Between C/C, C/C-SiC and Metallic Composite Materials

In-situ friction and wear study of SiCα/SiCβ and Al2O3-TiC-Co composite ceramics

SiC Nanowire–Si 3 N 4 Nanobelt Interlocking Interfacial Enhancement of Carbon Fiber Composites with Boosting Mechanical and Frictional Properties

The Microstructure and Wear Characteristics of Cu–Fe Matrix Friction Material with Addition of SiC

Dry sliding tribological behavior of C/SiC under different load and speed

Fibre-reinforced multifunctional SiC matrix composite materials

Effect of fiber orientation on tribological properties of fiber reinforced C/C‐SiC composites mated with ceramic ball

Effects of carbon fiber dispersion on bending property of Cf/SiC brake materials

Fabrication and Characterization of ZrO_2/SiC Composite Materials