Abstract:The existence mode of Y is an important factor affecting the oxidation resistance of NiCrAlY coating. The traditional thermal sprayed NiCrAlY coating had some problems such as internal-stress-induced coating peeling, when it was used at high temperature for a long time. In this paper, Y-modified NiCrAlY coatings were prepared on the surface of thermal-sprayed NiCrAlY coatings by halide-activated pack-cementation technology. The microstructure and oxidation resistance of the coatings after thermal insulation at 1100 °C for 100 h were analyzed. The results show that the oxidation resistance of Y-modified NiCrAlY coatings was improved significantly. When the oxidation temperature and time were 1100 °C and 100 h, the oxidation weight gain of thermal sprayed NiCrAl0.5Y and NiCrAl1.0Y coatings was 3.8 and 2.2 times that of Y-modified coatings, respectively. In addition, the NiCrAlY coatings prepared by pack cementation had better oxidation resistance than thermal sprayed coatings when the content of Y was equal. The oxidation resistance of the pack-cemented NiCrAlY coatings were increased with the increase in Y content when it was in a range of 0~1 wt.%. When oxidized at 1100 °C for 100 h, the oxidation weight gain of the pack-cemented NiCrAl0.5Y and NiCrAl1.0Y coatings was about 1.8 and 0.9 mg/cm2, respectively. The formation of highly stable intermetallic compounds Ni5Y in the pack-cemented Y-modified coatings is concluded to be the reason for improving the oxidation resistance of the coatings. This work can provide a solution to improve the oxidation resistance of traditional MCrAlY coatings.

Characterization of isothermal oxidation of air plasma sprayed NiCrAlY coatings

Air plasma sprayed high-entropy AlCoCrFeNiY coating with excellent oxidation and spallation resistance under cyclic oxidation at 1050–1150 °C

Isothermal Oxidation Behavior of Nicocraltay Coating Deposited by High Velocity Air-Fuel Spraying

Oxidation behavior at 1100 °C of NiCrAlY coatings deposited by various PVD techniques

Mechanical, Tribological, and Oxidation Resistance Properties of NiCrAlY Coating by Atmospheric Plasma Spraying

Investigation on the Oxidation Behavior of the NiCrAlY Bond-Coat with Low Al Content Sprayed by High Velocity Oxygen Fuel Method

Air Plasma Spraying of MCrAlY Coatings with Low Oxide Content Enabled by Adding a Deoxidizer

Temperature Effect on Early Oxidation Behavior of NiCoCrAlY Coatings: Microstructure and Phase Transformation

Oxidation Behavior of Nanostructured NiCrAlY Coating Deposited by Cold Spray

Microstructure and Oxidation Behaviour of Plasma-Sprayed NiCoCrAlY Coatings with and Without Ta on Ti44Al6Nb1Cr Alloys

Oxidation behavior of laser remelted plasma sprayed NiCrAlY and NiCrAlY–Al2O3 coatings

Microstructural Design and Oxidation Resistance of Conicraly Alloy Coatings in Thermal Barrier Coating System

Study on Microstructure and Oxidation Resistance Mechanism of Y-modified NiCrAlY Coating Prepared by Pack Cementation

Surface Microstructure and High Temperature Oxidation Resistance of Thermal Sprayed NiCoCrAlY Bond-Coat Modified by Cathode Plasma Electrolysis

High Temperature Oxidation Behaviors of Ni-Cr Based Thermal Sprayed Coatings

Oxidation Behavior of Graded NiCrAlYRe Coatings at 900, 1000 and 1100 °C

Microstructure features of cold-sprayed NiCoCrAlTaY coating and its high temperature oxidation behavior

Oxidation Behaviour of Microcrystalline Ni-Cr-Al Alloy Coatings at 900°C

Oxidation Behaviour of Sputter-Depositedni–cr–al Micro-Crystalline Coatings

Microstructure evolution and high temperature air oxidation behaviour of thick Cr coatings at 1200°C

Study of Oxidation Behavior of Nanostructured Nicraly Bond Coatings Deposited by Cold Spraying