Abstract:The biocompatible hydroxylapatite (Ca10(PO4)6(OH)2) (HA) coating is usually depositing on the titanium substrate to enhance the healing process of implant and to isolate it from the harsh body environment. However, poor mechanical properties of HA restrict its usage for orthopedic applications like hip and knee joints which have to bear the load. The biocompatibility is provided by HA and mechanical strength by the addition of reinforce with HA. Thermal post treatments have been mostly utilized to enhance the morphological and physicomechanical characteristics of as-deposition coatings. In the present research, the emphasis has been laid to analyze the outcome of thermal-processing on phases of hydroxyapatite in coatings developed by plasma spraying process. The surface-morphology of as-sprayed and thermally-processed, HA coated samples was studied using Scanning electron microscope (S.E.M.), Elemental-mapping, X-ray diffraction analysis (X.R.D.), and Fourier-transform infrared (F.T.-I.R.) spectroscopy techniques. The outcomes achieved from the X.R.D. analysis of the hydroxylapatite-coated samples after thermal-treatment reveal the formation of crystalline structure at 750°C with some traces of CaO. Moreover, when the heat treatment was further done at 950°C, the unwanted CaO was totally eliminated and coating with crystalline structure was obtained. No substrate element is visible in the X-ray mapping of coatings. The presence of ultrafine particles was observed on both substrates after the heat treatment of coatings at specified temperatures for 2hr in air. These ultrafine particles have the capability to bond with the bone and also helps for bone in-growth on their surfaces.

HYDROXYAPATITE THIN FILMS ON TITANIUM DEPOSITED BY KrF LASER

Synthesis and Characterization of Zn-substituted Hydroxyapatite Coatings by Electrochemical Deposition

Morphologies of Hydroxyapatite Crystal Deposited on Titanium Surface with Electrochemical Technique

Effect of Supersaturation on the Morphology of Hydroxyapatite Crystals Deposited by Electrochemical Deposition on Titanium

Pulsed laser deposition of hydroxyapatite thin films under Ar atmosphere

The Target Morphology During Pulsed Laser Deposition of Hydroxyapatite Thin Films

Preparation of Fluoridated Hydroxyapatite Coatings on Titanium by Electrolytic Deposition and Its Ftir Characteristics

Hydroxyapatite Coating with Strong (002) Crystallographic Texture Deposited by Micro-Plasma Spraying

Laser-induced Three-Dimensional Deposition of Calcium Phosphate on Porous Ti6Al4V

Atomic Layer Deposition and Characterization of Biocompatible Hydroxyapatite Thin Films

Osteoblast Responses to Thin Nanohydroxyapatite Coated on Roughened Titanium Surfaces Deposited by an Electrochemical Process.

Influence of Laser Remelting on the Microstructure and Phases Constitution of Plasma Sprayed Hydroxyapatite Coatings

High crystalline hydroxyapatite coating by eclipse type pulsed-laser deposition for low annealing temperature

Investigation on Bioactivity of Titanium Dioxide Thin Films Fabricated by Electron Cyclotron Resonance Plasma Aided Pulsed Laser Deposition

Hydroxyapatite Film Coating by Er:YAG Pulsed Laser Deposition Method for the Repair of Enamel Defects

PREPARATION AND PROPERTIES OF LANTHANUM-DOPED HYDROXYAPATITE COATING ON COMMERCIALLY PURE TITANIUM

Microstructure of Laser Cladding Hydroxyapatite Bioceramic Gradient Coatings

Characterization of Plasma Sprayed Hydroxyapatite Coating

Characterization and Stability of Hydroxyapatite Coatings Prepared by an Electrodeposition and Alkaline-Treatment Process

Development of Research on Hydroxyapatite (HAP) Bioceramic Coating Fabricated by Pulsed Laser Deposition

Impact of post-heat-treatment on the surface-roughness, residual stresses, and micromorphology characteristics of plasma-sprayed pure hydroxyapatite and 7%-Aloxite reinforced hydroxyapatite coatings deposited on titanium alloy-based biomedical implants