Abstract:New developments in instrumentation for ocean environmental engineering are allowing unprecedented levels of trace contaminant measurement in the deep ocean. With funding from the U.S. National Science Foundation (NSF), our engineering design team constructed a new mass spectrometer-based in situ analysis system for work in the deep ocean environment over prolonged deployment periods. Our design goals were a depth capability of up to 4,000 m water depth (400 bars hydrostatic pressure) and autonomous operation for periods of up to six months to a year, depending upon the type of external battery system used or other deployment circumstances, e.g., availability of a power cable or fuel cell power source. We chose a membrane introduction mass spectrometry (MIMS) sampling approach, which allows for dissolved gases and volatile organics introduction into the mass spectrometer vacuum system. The MIMS approach and the hydrophobic, silicon-coated membrane chosen both draw upon our previous experience with this technology in the deep ocean. The membrane has been tested to 400 bars in a series of long-term hydrostatic pressure tests, which extend the 200-bar working depth rating of this membrane by a factor of 2. Long-term deployment capability of the moderately powered, approximately 100 W system, was accomplished by power management of the embedded computer system and custom electronics with Windows-based and custom software now fully-developed and bench tested. The entire system fits within a 6.5-inch outside diameter pressure housing that is approximately five feet long. It consists of a 1 to 200 amu range quadrupole mass spectrometer equipped with Faraday and electron multiplier detectors, compact turbo-molecular and backing diaphragm vacuum pumps, internal rechargeable batteries, and internal waste vacuum chamber. Sample routing past the MIMS is accomplished by computer-controlled solenoid valves. We designed the pressure housings of both 6AL4V and type 2 titanium alloys that are rated to working depths of >4,000 m and are essentially corrosion proof over long-term deployments. We designed and integrated a fail-safe valving system for both rapid response to high-pressure MIMS failure and a pressure-switch circuit and high-pressure solenoid valve to detect and protect against slow leaks of the MIMS. To route sample waters to the MIMS-based instrument, we also designed and built a rugged plastic plenum that couples to the face of the sampler head, the latter of which consists of the MIMS inlet and a full-ocean rated thermister temperature probe with an operational range from −5 to 50°C. These instrumentation innovations will be described in the paper.

Integrated In-Situ Chemical Sensor System for Submersible Deployment at Deep-Sea Hydrothermal Vents

Development and application of chemical sensor for hydrothermal vents detection

Measurement and control system for gas-tight deep-sea water sampler based on LabVIEW

Integration of Real-Time Chemical Sensors for Deep Sea Research

Multi-Channel Data Logger Of In-Situ Chemical Sensors For Seafloor Hydrothermal Vents

Recent Developments Of Exploration And Detection Of Shallow-Water Hydrothermal Systems

A Pressure-Triggered Isobaric Sequential Liquid Sampling System for Full-Ocean-depth: Design and Field Deployment

A Long-Term in Situ Calibration System for Chemistry Analysis of Seawater

Development of a deep-sea hydrogen sulfide ion sensor and its application for submarine hydrothermal plume exploration

A Deep-Ocean Mass Spectrometer to Monitor Hydrocarbon Seeps and Pipelines

Development of an Easy-to-Operate Underwater Raman System for Deep-Sea Cold Seep and Hydrothermal Vent In Situ Detection

A deep-sea in-situ chemical laboratory for cabled seafloor observatories

Mechatronic Integration and Implementation of in Situ Multipoint Temperature Measurement for Seafloor Hydrothermal Vent

The Optimization of Ag/Ag2s Electrode Using Carrier Electroplating of Nano Silver Particles and Its Preliminary Application to Offshore Kueishan Tao, Taiwan

A Multi-Channel Data Logger of In-Situ Chemical Sensors for Cabled Seafloor Observatories

High-resolution Quasi-Distributed Temperature and Pressure Sensing System for Deep-Sea Reservoir Monitoring

Development of an Electric Control Gas-Tight Sampler for Seafloor Hydrothermal Fluids

Design of deep-sea chemical data collector for the seafloor observatory network

Midinfrared Sensor System Based on Tunable Laser Absorption Spectroscopy for Dissolved Carbon Dioxide Analysis in the South China Sea: System-Level Integration and Deployment

In Situ High-Precision Measurement of Deep-Sea Dissolved Methane by Quartz-Enhanced Photoacoustic and Light-Induced Thermoelastic Spectroscopy

Novel gas-tight multi-sampler for discrete deep-sea water