Abstract:Laser speckle is a new technology for non-destructive detection in agriculture. When laser light with good coherence irradiates on the optically rough surface or the surface with some kind of activity, the scattering light will interfere with each other and form a mottled pattern called laser speckle. The laser speckle contains various information of the reflector, such as the roughness, the particle’s motion and the temperature information. Huangguan pears were used as the object in this research to investigate the possibility of identifying the defects from the stem/calyx and the sound area of pears based on laser speckle technology. A laser speckle imaging system was established which contained a semiconductor laser (635 nm, 50 mw) applied as the light source and a digital signal generator applied as the trigger source of the CCD (charge coupled device) camera. Two hundred pears including one hundred sound pears and one hundred pears with the defect (rot) were tested. The speckle images of defect (rot) parts and good parts (calyx/stem, sound area) of the pears were collected under the same condition. First of all, the speckle images were converted into the grayscale images using Matlab 2011b. The method of Fujii and the weighted generalized differences method (WGD) were used to analyze the grayscale speckle images to get the images of Fujii and WGD. Then gray level co-occurrence matrix (GLCM) was used to extract the mean and the standard deviation values of the angular second moment (ASM), entropy (ENT), moment of inertia (INE) and correlation (COR) from the images of Fujii and WGD, respectively. Therefore, in total, 16 features were extracted. The performance of each feature was evaluated by the receiver operator characteristic (ROC) curve. According to the ROC curves, the features whose values of the area under the curves (AUC) were higher than 0.5 were chosen for further analysis. The best threshold value of each selected feature was calculated by Youden’s index. The classification analysis based on single feature was tested using the best threshold value. Besides, the classification analysis based on multiple features was carried out by the binary logistic regression. The combination of every two features was tested to get better classification accuracy. The results showed that there were seven features whose AUC values were bigger than 0.5. In classification of single feature, the ASM extracted from WGD image had the best performance whose overall accuracies of calibration and validation sets were 96.4% and 96.7% respectively. In classification of multiple features, the combination of the ASM and standard deviation of correlation extracted from WGD image had the best performance whose overall accuracies of calibration and validation sets were both 97.5%. In order to find out the causes of the error, the original RGB (red, green and blue) images of the misjudged samples were studied. It turned out that the defect area which was misjudged to be normal was not obvious. Besides, the defect area was larger than the light spot whose diameter was 20 mm which could not cover the defect area completely. Therefore, the texture features of laser speckle images of misjudged samples were closer to the sound area than the defect area, which led to the miscalculation. This research shows that the method of laser speckle imaging is feasible in the detection of pear defect (rot) and stem/calyx.

Laser Scatter Feature of Surface Defect on Apples

Pear defect and stem/calyx discrimination using laser speckle

A Novel 3D Evaluation Method for Surface Defects Using Broadband Laser-Generated Rayleigh Waves with Wavenumber Analysis.

A high-resolution detecting system based on machine vision for defects on large aperture and super-smooth surface

Quantitative Detection of Surface Defect Using Laser-Generated Rayleigh Wave with Broadband Local Wavenumber Estimation

Hyperspectral Reflectance Imaging for Detecting Typical Defects of Durum Kernel Surface

Detection of Defects in Optics Based on Scanning

Surface defects evaluation system based on electromagnetic model simulation and inverse-recognition calibration method

Application of Machine Vision in Identifying Size And Surface Defect of Huanghua Pear

Inspecting Diameter and Defect Area of Fruit With Machine Vision

Multi-Band-Image Based Detection of Apple Surface Defect Using Machine Vision and Deep Learning

Real-Time Grading of Defect Apples Using Semantic Segmentation Combination with a Pruned YOLO V4 Network

Automatic Detection of Common Surface Defects on Oranges Using Combined Lighting Transform and Image Ratio Methods

Nondestructive Detection Of The Internal Quality Of Apple Using X-Ray And Machine Vision

ON APPLE QUALITY GRADE IDENTIFICATION BASED ON MACHINE VISION

Spatial Frequency Domain Imaging System Calibration, Correction and Application for Pear Surface Damage Detection

Width and Depth Gauging of Rectangular Subsurface Defects Based on All-Optical Laser-Ultrasonic Technology

Detecting Technique for Surface Texture on Apples Based on Machine Vision

On-spot Evaluation of Maturity Stage of Fruits Based on 655 Nm Laser-induced Photoluminescence of Chlorophyll-α

A Method of Size Inspection for Fruit with Machine Vision

Inspection and Grading of Surface Defects of Fruits by Computer Vision