Abstract:Powder coatings are gaining popularity for their economic and environmental benefits. Additives (pigments) such as zinc phosphate enhance the anti-corrosive properties of coatings, but their behavior in powder coatings has not been extensively studied. In this study, zinc phosphate was incorporated into three powder coating systems: polyester clearcoat, polyester and epoxy coatings with filler BaSO4. Neutral salt spray and electrochemical tests (OCP, LPR, and EIS) confirmed that the anti-corrosive performance improved with the addition of zinc phosphate. The optimal additive dosage was determined to be 2% for all of the coating systems studied here, based on salt spray tests. Here, the time until failure increased by 1.5 to 2 times. Using electrochemical tests, an optimal additive dosage of 8% was found for the polyester clearcoat, while the other coating systems maintained an optimal additive dosage of 2%. Performance increased by as much as one order of magnitude based on resistance/impedance measurements. This suggested a synergistic effect between the additive and the filler. The passivation layer was confirmed by both X-ray diffraction and Raman spectroscopy. Based on the results and discussion presented in this article, the discrepancy was caused by different features of the two tests, such that the electrochemical tests probe the function of intact coatings, whereas salt spray measures only the corrosion spreading from the scribe. It is proposed that the two test methods characterize different aspects of the coatings, corresponding to their service conditions. This has theoretical and practical significance in the evaluation of anti-corrosive coatings. Other properties of the coatings, including adhesion, gloss, distinctness-of-image, and pencil hardness, were measured as per applicable standards and the conformance was verified.

PREPARATION OF ANTICORROSIVE COATING WITH LAMELLAR ZINC PARTICLES

Preparation and Corrosion Performance of Electrophoretic Epoxy Coatings Doped with ZrO2

Comparative Study of Carbonaceous and Polymer Conductive Additives on Anticorrosion Performance of Epoxy Zinc-Rich Primer

Fabrication of a Conductive Additive for the Anticorrosion Enhancement of Zinc-Rich Epoxy Coatings

An EIS analysis on corrosion resistance of anti-abrasion coating

Enhanced anticorrosion performance of zinc rich epoxy coatings modified with stainless steel flakes

Assessment of Anticorrosion Performance of Zinc-Rich Epoxy Coatings Added with Zinc Fibers for Corrosion Protection of Steel

Effect of iron powder on zinc reactivity and anticorrosion performance of zinc-rich epoxy coatings

STUDY OF THE ELECTROCHEMICAL BEHAVIORS OF THE ZINC-RICH PAINTS BASED MULTILAYER ORGANIC COATINGS IN NaCl SOLUTION

A Comparative Study on the Anti-Corrosive Performance of Zinc Phosphate in Powder Coatings

Flake-like ZnAl alloy powder modified waterborne epoxy coatings with enhanced corrosion resistance

Surface Modification With Zinc and Zn-Ni Alloy Compositionally Modulated Multilayer Coatings

Zeolitic imidazolate frameworks dispersed in waterborne epoxy resin to improve the anticorrosion performance of the coatings

Waterborne corrosion-resistant hydrophobic alkyd resin composite coatings modified with fluorinated acrylate–siloxane and submicron-sheet zinc phosphate pigment

Influence of Zinc Content and Surface Contamination on the Electrochemical Behaviors of Epoxy Zinc-Rich Primer

Preparation and Properties of Anti-corrosion Multifunctional Fluorocarbon Coatings

Preparation and properties of polyurethane cold galvanizing coatings with phosphoric acid modified zinc powder

Corrosion protection of PPy-Ti3C2-modifed epoxy zinc-rich coatings in dilute NaCl solution

Synergistic Effect between Zinc Particles and Graphene on the Anti-Corrosion Performance of Epoxy Coatings

Preparation of a novel 2-amino benzothiazole loaded ZIF-8/layer double hydroxide composite and its application in anti-corrosion epoxy coatings

Novel Anticorrosion Property of Organic Coating Based on Liquid Metal