Abstract:Periodic micro/nano-structure has been playing an important role in microelectronics,microfluidics,micro/nano-optics.There are many technologies that have been proposed for structure manufacture,for example,photolithography,electron beam etching technique,nanoimprint technology.Although these technologies have their advantages,it is troubled by template production,corrosion solution and material choices.Multi-beam interference is one of the common technologies for fabrication of periodic structures as sacrificial layer.It is widely used for its easy setup,quick,and low cost capacities.Laser processing has the advantages of direct writing by light-absorbing under high energy density of pulsed laser of low costs,high quality,fine precision,non-fiat three dimensional fabrication ability in transparent medium.Herein,based on principle of interference lithography especially four-beam interference and laser ablation,we proposed one step method of fabrication of large-area mocro/nano-structures by multiple beam laser interference ablation technology.As we all know,light intensity would be redistributed and represent periodic strong and weak variation.Quanta-Ray Nd:YAG Laser of wavelength 355 nm,repetition of 10 Hz and pulse duration of 10 ns was used for laser interference ablation with maximum power 1100 mW and diameter of 10 mm.Area under high light intensity above the threshold will be ablated and removed,while area under low light intensity below the threshold will be left.Thus with this periodic intensity distribution in multiple beam interference and the ablation mechanism,two-dimensional periodic structures in large area can be fabricated maskless on zinc sulfide (ZnS) surface in one step.Additionally,the experiment is in normal atmosphere and donnot need vacuum,which makes it easy and low cost.Structure with period of 3 μtm at incident angle of 4.8° was chosen for example to investigate the transition of structure type,as well as the morphology evolution with exposure time in detail.While the incident angle of any beam is slightly changed,the two-dimensional distribution will break into two types,both of which have its own distribution.At the same time,these two types are distributed periodically.In our experiment,periodic holes and pillars were fabricated repeatedly on ZnS surface in the inte rference ablated area with a larger period about 74 μm.Periodic holes were of period 3 μm while pillars were of period 3 μm 1/√2.Distribution directions of pillars were 45° titled with that of holes.Further,the phenomenon of phase shift was studied by adjusting the incident angle of one beam in theory,which explained the experiment results well.At last,according to our study in recent years,the opportunity and challenge of multiple-beam interference ablation technology was discussed in this article.We are believed this interference ablation technology will be taking an important role in hard material processing,two dimensional periodic and quasi-periodic structure fabrication,OLED,solar cells and many more potential micro and nanotechnology regions.

Periodic Micro-Structures Fabrication On Glass With Co2 Laser

Formation of Periodic Structures on Glass with Laser Irradiation

Periodic Microstructures Induced by Interfered Femtosecond Laser Pulses

Formation Of Two-Dimensional Periodic Microstructures By A Single Shot Of Three Interfered Femtosecond Laser Pulses On The Surface Of Silica Glass

Multi-photon Fabrication of Two-Dimensional Periodic Structure by Three Interfered Femtosecond Laser Pulses on the Surface of the Silica Glass

Periodic Microstructures Fabricated by Laser Interference with Subsequent Etching

Laser‐Induced Transitions of Azo Molecular Glass Pillar Arrays: A New Way to Fabricate Periodic Complex Surface Patterns Upon Linearly Polarized Radiation

Femtosecond laser-induced large area of periodic structures on chalcogenide glass via twice laser direct-writing scanning process

Evolution of Femtosecond Laser-Induced Periodic Structures: from Nanoholes to Regular Structures

Formation and Applications of Periodic Structures in Transparent Materials Induced by Single Fs Laser Beam

Shape- and Size-Controllable Microstructure on Glass Surface Induced by Femtosecond Laser Irradiation.

On the conversion of point-to-linear hierarchical micro/nano-structures on the glassy carbon surface by nanosecond pulsed laser irradiation

Glass structure changes in CO2-laser writing of long-period fiber gratings in boron-doped single-mode fibers

Investigation on Femtosecond Laser-Assisted Microfabrication in Silica Glasses

Orientable Nonlinear Optical Crystals and Periodic Nanostructure by Femtosecond Laser Irradiation

Ultrafast Laser Inducing Continuous Periodic Crystallization in the Glass Activated via Laser‐Prepared Crystallite‐Seeds

Generation of Periodic Micro- and Nano-Structures by Parameter-Controlled Three-Beam Laser Interference Technique

Polarization-dependent Microstructural Evolution Induced by a Femtosecond Laser in an Aluminosilicate Glass

Grating Fabrication with CW CO2 Laser Irradiation

Periodic Structures Fabricated by Nanosecond Laser Four-Beam Interference Ablation

Formation of Periodical Sub-Micron Sized Structures on Silicon by Interfered Nanosecond Laser Pulses