Study on Self-compacting Concrete of Textile Reinforced Concrete

XU Shi-lang,LI He

DOI: https://doi.org/10.3969/j.issn.1007-9629.2006.04.020

2006-01-01

Abstract:A kind of self-compacting concrete that is fit for textile reinforced concrete(TRC,for short) was studied in this paper.On the base of experimental results of self-compacting capability and mechanical properties,the self-compacting concrete is proved to be used in TRC.

What problem does this paper attempt to address?

Compressive Behavior of GFRP Tubes Filled with Self-Compacting Concrete

Pan Xie,Lik Lam,Tao Jiang

DOI: https://doi.org/10.1061/jccof2.cceng-3937

2023-01-01

Journal of Composites for Construction

Abstract:Self-compacting concrete (SCC) features excellent flow ability without the need of vibration for compaction during casting. This makes it particularly suitable for application in hybrid fiber-reinforced polymer (FRP)-concrete-steel double-skin tubular columns (DSTCs), a high-performance structural form evolved from concrete-filled FRP tubes (CFFTs). In a DSTC, the space between the inner steel tube and the outer FRP tube for filling concrete may be narrow and the application of vibration may be difficult. However, because of the large shrinkage of SCC compared to traditional concrete of normal flow ability, the integrity and composite action of DSTCs with SCC become a major concern. To clarify this issue, an understanding of the behavior of CFFTs filled with SCC is an essential prerequisite. While a large number of studies have been published on CFFTs with normal concrete (NC), only limited studies have been carried out on CFFTs with SCC. This paper presents a comprehensive investigation on the effect of SCC on the behavior of large-scale CFFTs. Axial compression tests were carried out on concrete-filled glass FRP (GFRP) tubes with diameters of 150, 200, 300, and 400 mm. The compressive behavior of the CFFT specimens filled with NC, a nonexpansive SCC, and an expansive SCC (ESCC) was compared and discussed. The results showed that the specimens with nonexpansive SCC behaved differently compared to those with NC as a result of larger shrinkage, especially for large specimens for which the confinement level was lower. This situation, however, improved in specimens where ESCC was used. Finally, the test results were further analyzed using a theoretical model recently proposed by the authors' group.
Bond Investigation Of Hybrid Textile With Self-Compacting Fine-Grain Concrete

Shiping Yin,Bo Wang,Fei Wang,Shilang Xu

DOI: https://doi.org/10.1177/1528083716629137

2017-01-01

Journal of Industrial Textiles

Abstract:This paper presents an experimental investigation into the influence of bond characteristics between textile and matrix on the mechanical behavior of textile-reinforced concrete (TRC). Two types of tests were performed, i.e. pullout test and uniaxial tensile test. Self-compacting fine-grain concrete was adopted. Two kinds of hybrid textile, consisting of both carbon and E-glass yarns, were specially prepared for this study. The experimental results show that sticking sands on the textile after epoxy resin impregnation can improve the interfacial property between textile and matrix. The specimens with textile of 10mmx10mm mesh have stronger bond strength than those with textile of 25mmx25mm mesh, and can reach the maximum tensile strength of yarns when the initial bond length is between 30mm and 35mm. Moreover, sticking sands on the textile can improve the multiple cracks form and the ultimate bearing capacity of TRC under uniaxial tensile load. Specimens with textile of 10mmx10mm mesh have higher first-crack loads than those with textile of 25mmx25mm mesh whether or not the textile surface treatment was conducted, and also have better crack distribution. Finally, based on the experimental results from TRC under uniaxial tensile load, a double linear constitutive equation of stress-strain relationship of carbon fiber yarn is provided in this paper.
A Study on Thin Concrete Plate Reinforced with Textile

LI He,XU Shilang

DOI: https://doi.org/10.3321/j.issn:1000-6869.2007.04.016

2007-01-01

Abstract:To understand the mechanism that textile restricts the cracking of concrete,the test of bond properties between fibers and concrete,and mechanism properties of textile reinforced concrete(TRC) one-way slabs under four-point loading were performed.The results proved that epoxy resin impregnating,sand covering,prestressing can improve the bond between fibers and concrete so that cracks of TRC slab become finer and the spaces between them become closer.Increasing the content of textile also improves the cracking behavior of concrete.Prestressing also increases cracking load and limiting load of TRC slab.The analyse of ultimate bearing moment and cracking behavior of TRC are performed based on plane cross-section assumption and the calculated results are in agreement with those gained in experiments.
Self-Compacting Concrete For Textile Reinforced Elements

He Li,Shilang Xu

DOI: https://doi.org/10.1617/2912143624.075

2005-01-01

Abstract:The textiles with rovings made of fiber-threads through basketry which are oriented parallel with the occurring stresses instead of randomly-dispersed short fibers in concrete can increase obviously the efficiency of fiber-reinforcing. Moreover, textiles have no risk of corrosion due to the ingress of chlorides and carbonation of concrete and are lightweight, flexible, high-strength as well as non-magnetic. Therefore, textile reinforced concrete structures are expected to have wide application foregrounds. In order to ensure that the bond between fiber and matrix and avoid pores, both of which influence the strength of the structure, the biggest grain size of matrix must be enough small and matrix must have a very nice workability and consistency so that they fully penetrate the textile. As prestressed textile reinforced concrete is concerned, the self-compacting capability of matrix is indispensable because vibration can influence the application of prestress. Therefore a new kind of self-compacting concrete (SCC) named as fine concrete is developed. The central task of this paper is development and optimization of the matrix in term of its chemical compatibility with the materials (alkali-resistant glass fibres) as well as a suitable consistency and workability based on test methods used for self-compacting concrete, rapid hardening, and high early strengths, for planned production processes.
Bond Properties and Experimental Methods of Textile Reinforced Concrete

Xu Shilang,Li He

DOI: https://doi.org/10.1007/s11595-006-3529-9

2007-01-01

Journal of Wuhan University of Technology-Mater Sci Ed

Abstract:Textile reinforced concrete(TRC, for short) allows the low size production and offers a high effectiveness of the reinforcement by using continuous roving instead of short-chopped fibers. However, whether textiles can cooperate with concrete very well depends on the bond between them. In this paper, the bonding mechanism that the stress was transferred from fine concrete to textile was analyzed, and the influences of the initial bond length of textile, the surface treatment of textile, the strength and workability of concrete as well as the level of prestressing force on bond behavior were investigated on the basis of pull-out tests. The results reveal that with initial bond length increasing, the maximum pull force increases, and increasing concrete strength and improving workability of concrete matrix, epoxy resin impregnating and sand covering of textile as well as prestressing textile can obviously increase the bond strength between the textile and concrete.
Investigation on the flexural behavior of reinforced concrete beam strengthened with textile-reinforced concrete

Xu Shilang,Yin Shiping,Cai Xinhua

DOI: https://doi.org/10.15951/j.tmgcxb.2011.04.012

2011-01-01

Abstract:From the point of improving the interfacial bond between the textile and the fine grained concrete in textile reinforced concrete(TRC) and the interfacial characteristics of old and new concrete,the flexural performance of reinforced concrete(RC) beams strengthened with TRC was studied.The experimental results show that sticking sands on the epoxy resin-impregnated textile can make its anti-crack ability better exerted and thus the crack-control and reinforcing function of TRC layer can be fully utilized,and embedding U-shaped pins into the old concrete contributes to improve the whole mechanical behavior of RC beams strengthened with TRC,but smearing interfacial agent on the surface of the old concrete has almost no effect on the beams.In addition,mixing polypropylene fiber into fine grained concrete is helpful to enhance the initial cracking load of the component,and when the ratio of steel reinforcement is constant,increasing the ratio of textile reinforcement in TRC can effectively delay the development of main cracks of the structure,and decrease the crack width and the crack spacing and significantly improve the yield load and ultimate bearing capacity of the beams.Finally,based on the bending design theory of RC elements,this paper simulates the curves of load vs.mid-span deflection of RC beams reinforced with TRC.Comparison between the calculated and the experimental results reveals satisfactory agreement and thus verifies that the calculation method is practicable.
Experimental study on mechanical properties of Textile Reinforced Concrete (TRC)

G. Karthikeyan,A. Leema Margret,V. Vineeth,R. Harshani

DOI: https://doi.org/10.1051/e3sconf/202338704002

2023-01-01

E3S Web of Conferences

Abstract:Textile-reinforced concrete (TRC) is a variant of reinforced concrete in which textiles are used in place of steel reinforcing bars. Reinforcing the concrete with steel means increasing its tensile strength, but steel also corrodes and wears out over time. The TRC is a novel idea that has the potential to overcome these drawbacks. TRC is a composite reinforcing material that is made from cement and has the benefits of being resistant to corrosion, having a high bearing capacity, and performing well in terms of its fracture limit. The principal function of TRC in buildings has been as reinforcement and as a means of enhancing the ductility and performance of concrete. This experimental work utilizes a 145 gsm (grams squared per meter) alkali-resistant (AR) glass fiber textile mesh. Specimens were cast with and without fibers, and the number of layers was increased from 1 to 3 at 25 mm spacing. In this experimental work, the mechanical behavior of TRC was investigated by conducting tests on its impact, compressive, and flexural strengths. From these results, the TRC specimen exhibits more flexibility than the control specimen. The TRC specimen bends under force and returns to a new position when the load is removed, indicating a good energy absorption capability. As a result, it infers that the specimen with fibrehave the capacity to withstand a higher maximum load than conventional specimens. TRC has a greater fracture control system compared to conventional steel-reinforced concrete.
Mechanical properties research of textile reinforced concrete

徐世烺,戴清如,李庆华,沈玲华

DOI: https://doi.org/10.13243/j.cnki.slxb.2012.s1.004

2012-01-01

Abstract:Textile reinforced concrete (TRC) is a new cement-based composite material. It is the combination of directional fiber braid and high-performance fine concrete. Since 1999, DFG established SFB532 and SFB528 Research Center at RWTH Aachen University and began a systematic study of materials and structures on the TRC. Due to the excellent tensile strength and durability of fiber materials, the thickness of concrete cover is required to meet the anchoring requirements only. Therefore, the fiber is fit for thin-walled lightweight materials. The experiment studied the mechanical properties of hybrid carbon/glass fiber braid and basalt/glass fiber hybrid braid, a high-performance concrete and the TRC sheet. The aim is to develop a thin-walled structure of the TRC, which is suitable for plug-in building curtain wall. The results show that a high discrete of fiber tensile strength. And the tensile property of basalt fiber is lower than the carbon fiber. In addition, the high-performance fine concrete shows strong liquidity, compact structure, high strength, moderate shrinkage, and good interfacial adhesion, which is suitable for industrial use. Lastly, the bending performance of TRC plate with carbon fiber is good but the reinforced effect of basalt fiber is not obvious.
Improved Mechanical Properties of Textile Reinforced Concrete Thin Plate

Shiping Yin,Shilang Xu,Hedong Li

DOI: https://doi.org/10.1007/s11595-013-0647-z

2013-01-01

Journal of Wuhan University of Technology-Mater Sci Ed

Abstract:Textile reinforced concrete (TRC) is especially suitable for the thin-walled and light-weight structural elements with a high load-bearing capacity. For this thin element, the concrete cover thickness is an important factor in affecting the mechanical and anti-crack performance. Therefore, the influences of the surface treatment of the textile and mixing polypropylene fiber into the concrete on the properties of the components with different cover thickness were experimentally studied with four-point bending tests. The experimental results show that for the components with the same cover thickness, sticking sand on epoxy resin-impregnated textile and adding short fiber into the concrete are helpful to improve their mechanical performance. The 2–3 mm cover thickness is enough to meet the anchorage requirements of the reinforcement fiber and the component has good crack pattern and mechanical behavior at this condition. Comparison between the calculated and the experimental values of flexural capacity reveals satisfactory agreement. Finally, based on the calculation model of the crack spacing of reinforced concrete structures, the crack extension of this thin-wall component was qualitatively analyzed and the same results with the experimental were obtained.
Investigation on the Flexural Behavior of Concrete Members Reinforced with Epoxy Resin-Impregnated Textiles

S. P. Yin,S. L. Xu,F. Wang

DOI: https://doi.org/10.1617/s11527-013-0174-6

2013-01-01

Materials and Structures

Abstract:Textile reinforced concrete (TRC) members reinforced with the fiber materials: AR glass or carbon having no plastic capacity have no distinct failure symptom when the ultimate load is reached, and this limits their application to load-bearing. Therefore, in this research, a new method of adding thin steel bars into TRC was studied and the analytical prediction of the flexural response of TRC members was investigated. Two types of specimens (Series A and Series B) were prepared to verify the validity of the bending theory. Results from Series A specimens show that the compression constitutive models of concrete adopted in this study show no significant influence on the calculated results, and the experimental results of the specimens reinforced only with the textile have the same trend as the calculated results. Results from Series B specimens indicate that the abrupt fracture of TRC can be overcome by a combination of textile and steel bars with high ductility. Comparison between the calculated results and the experimental results of the specimens with textile and thin steel bars reveals satisfactory agreement.
Experimental Study of Uniaxial Compression Properties of High Performance Fine Grained Concrete

YIN Shi-ping,XU Shi-lang

2009-01-01

Abstract:As a result of high bearing capability,excellent ductility,resistance to corrosion,no magnetizing,thin wall and light weight,the textile reinforced concrete(TRC)is expected as one of the most promising structural elements in the 21st century.For the fine grained concrete used as matrix for TRC,there are currently no straightforward methods to research into the mechanical properties such as σ-e curves,compressive,flexural and tensile strengths.For popularization and application of TRC,the compressive properties and stress-strain curve of the fine grained concrete under uniaxial compression are studied by experiments.The experimental results show that compared with ordinary concrete with similar compressive strength,the Young's modulus of fine grained concrete is lower,and the strain at ultimate load is higher.When the experimentally determined control parameters are used,experimental curves show very good agreement with the calculated curves.
An Experimental Study on Improved Mechanical Behavior of Textile-Reinforced Concrete

shi ping yin,shi lang xu

DOI: https://doi.org/10.4028/www.scientific.net/AMR.168-170.1850

2011-01-01

Abstract:The influences of the mesh sizes, the surface treatment and cover thickness of the textile on anti-crack and bearing capacity of the competent were investigated. Additionally, to prevent the splitting of the concrete, hanging U-shaped hook upon textiles was also experimentally studied. The experiment results indicate that sticking sand on epoxy resin-impregnated textile and reduced cover thickness are helpful to improve the mechanical performance of the component; the textile with 10 mm x 10 mm mesh size is superior than that with 20 mm x 20 mm mesh size regardless of in the respect of enhancing the bearing capacity of the TRC or in the respect of controlling matrix cracking; the novel method of adding U-shape iron hook not only can improve the bonding performance between the textile and the concrete, but also can enhance the shearing capacity of the concrete.
An Investigation on Flexural Behavior of Reinforced Concrete Beam with Textile

Shi Ping Yin,Shi Lang Xu

DOI: https://doi.org/10.4028/www.scientific.net/amr.243-249.1008

2011-01-01

Advanced Materials Research

Abstract:The textile reinforced concrete (TRC) member has no distinct failure symptom when it arrives at its ultimate load. At the same time, ordinary steel-reinforced concrete (RC) elements have large dead weight and can not efficiently restrict the expansion of the main crack of structures. In order to overcome the above disadvantages, a new architecture reinforced with a combination of the textile and steel bar was presented in this study. The analytical formulae of the proper beam using this new structure were derived, including the load-carrying capacity at different stages and load vs. mid- span deflection relationship during the entire loading process. The theoretical values were compared with the experimental values. It is shown that the theoretical values coincide with the experimental values well and the feasibility of the formulae is verified.
Experimental Study on Mechanicial Properties of TRC Plate

Shilang Xu,Yiqun Yan

DOI: https://doi.org/10.4028/www.scientific.net/amr.150-151.766

2010-01-01

Advanced Materials Research

Abstract:Textile reinforced concrete is a rather promising structural material which improves characteristics of traditional materials in many ways. In this paper, based on uniaxial tension experiments of TRC plates, the loading behavior of TRC plates and influence factors on their ultimate load capacity are discussed. The main parameter in the experiments is textile ratio. With the increasing of textile ratio, the efficiency of fibers decreases in a linear way, and the cracking performance is ameliorated. Moreover, a calculation formula is proposed taking the textile ratio into consideration to forecast the ultimate bearing capacity of TRC plates. Finally, according to the mixture law and ACK model, the stress-strain curve of TRC plates is simplified as a trilinear model. Providing a theoretical foundation, this investigation extends further application of TRC in practice.
Mechanical Properties and Durability of Textile Reinforced Concrete (TRC)-A Review

Chao Wu,Yang Pan,Libo Yan

DOI: https://doi.org/10.3390/polym15183826

2023-09-19

Abstract:Textile reinforced concrete (TRC) is an innovative structure type of reinforced concrete in which the conventional steel reinforcement is replaced with fibre textile materials. The thin, cost-effective and lightweight nature enable TRC to be used to create different types of structural components for architectural and civil engineering applications. This paper presents a review of recent developments of TRC. In this review, firstly, the concept and the composition of TRC are discussed. Next, interfacial bond behaviour between fibre textile (dry and/saturated with polymer) and concrete was analysed considering the effects of polymer saturation, geometry and additives in polymer of the textile. Then, the mechanical properties (including static and dynamic properties) of TRC were reviewed. For static properties, the mechanical properties including compression, tension, flexural, shear and bond properties are discussed. For dynamic properties, the impact, seismic and cyclic properties were investigated. Furthermore, the durability of TRC under different environmental conditions, i.e., temperature/fire, humidity and wet-dry cycles, freeze-thaw, chemical and fatigue were discussed. Finally, typical engineering applications of TRC were presented. The research gaps which need to be addressed in the future for TRC research were identified as well. This review aims to present the recent advancement of TRC and inspire future research of this advanced material.
Mechanical properties of textile reinforced concrete plate at low textile ratios

徐世烺,阎轶群

DOI: https://doi.org/10.13801/j.cnki.fhclxb.2011.05.007

2011-01-01

Abstract:Uniaxial tensile experiments of textile reinforced concrete（TRC） plates and the results were detailed presented in this paper.Then the mechanical properties of textile reinforced concrete and its main influence factors on ultimate loading capacity were studied.And the concept of critical textile ratio was proposed.The mechanical properties of textile reinforced concrete plate were discussed at low textile ratios.When textile ratio was larger than the critical textile ratio,the ultimate bearing capacity exceeds the cracking load,and there was no sudden drop during the loading process.With the increase of textile ratio,the efficiency of fibers decreases in a linear way.And strength of fibers was not fully utilized.Moreover,the crack form was also investigated on different textile ratios.With the increase of textile ratio,cracking space reduces and cracking width decreases as well.Finally,according to the mixture law and ACK model,the stress-strain curve of TRC plates is simplified as a trilinear model.The calculation formula was proposed taking the textile ratio into consideration to forecast the ultimate bearing capacity of TRC plates.
Investigation on Bonding and Overlapping Performance of Textile in Fine Grained Concrete

YIN Shi-ping,XU Shi-lang,WANG Fei

DOI: https://doi.org/10.3969/j.issn.1007-9629.2012.01.007

2012-01-01

Abstract:The pull-out and four-point tests of thin-walled plate specimens were carried out to investigate the bonding and overlapping performance of textile in fine grained concrete.The experimental results show that the warp yarns and the surface treatment of the textile have significant influences on the interfacial bond performance between the textile and the fine grained concrete.In addition,for the textile covered with or without sand,with the increase of the initial bond length of carbon fiber yarn,the average interfacial bond strength has a falling trend,and when the initial bond length is longer than 35 mm,it is enough to ensure that carbon fiber yarns can have sufficient bond to the fine grained concrete and can not be pulled out.For the textile covered with fine sand,if the overlapping length of carbon fiber is longer than 60 mm,the requirement for the stress transfer between fiber yarns can be met.At the same overlapping length,the enhancement capacity of the textile using the binding overlapping are better than that of the textile using the sticking overlapping.
Analytical Theory of Flexural Behavior of Concrete Beam Reinforced with Textile-Combined Steel

ShiLang Xu,ShiPing Yin

DOI: https://doi.org/10.1007/s11431-010-3063-z

2010-01-01

Science China Technological Sciences

Abstract:Textile-reinforced concrete (TRC) is a new high performance cementitious composite material, which not only has superior corrosion resistance but also can effectively limit the development of concrete cracks and make the crack width and spacing of concrete become smaller. However, due to the brittle feature of fiber materials, the TRC structural member has no distinct failure symptom when it arrives at its ultimate load. At the same time, ordinary reinforced concrete (RC) elements have large dead weight and can not efficiently restrict the expansion of the main crack of structures because of the restriction of their special cover thickness. In order to overcome the disadvantages of both the TRC and the RC, a new architecture reinforced with textile- combined steel is proposed in this study, making full use of the advantages of the above two structures. The cover concrete at the tension zone of an RC element is partially replaced with TRC and thus the steel reinforcements replaced with textiles are subtracted. Compared with the old one, the new structure has less dead weight and has the merits of service safety and good durability. The flexural development process of the proper beam with this new structure is investigated in this paper and based on the plane section assumption, analytical equations are derived by using nonlinear analysis theory, including the load-carrying capacity at different stages and moment-curvature relationship and mid-span deflection during the entire loading process. Comparison between the calculated and the experimental results reveals satisfactory agreement and thus verifies the feasibility of the equations.
An experimental study on the flexural properties of carbon textile reinforced ECC

Shilang Xu,Qinghua Li,Hedong Li

DOI: https://doi.org/10.3321/j.issn:1000-131x.2007.12.009

2007-01-01

Abstract:It is well known that the failure mode of traditional cementitious composite components under tensile loading exhibits a macro single crack pattern. Engineered Cementitious Composites (ECC) typically possess strain hardening property, prominent toughness and superior durability, and the failure pattern of ECC components involves multiple fine cracks under tensile loading even at ultimate tensile strain. Textile reinforced concrete (TRC) is a new type of continuous long fiber reinforced cementitious composites. Rovings are placed along the direction of principal stress so that the reinforcing effect can be significantly enhanced. In order to develope new type of anticracking technique for concrete structures, a new cementitious composite reinforced by a combination of carbon textile and short-cut PVA fiber was proposed, and four-point bending experiments of specimens were performed. The experimental results show that crack resistance and control can be achieved when both carbon textile and short-cut PVA fiber are combined as reinforcements. Accordingly, the durability and service life of concrete structures would be greatly enhanced due to combining the advantages of both ECC and TRC. Comparing with TRC, the influences of the surface treatment of textile, water-binder ratio and volume content of PVA fiber on the crack resistance and bearing capacity of the new material were also investigated.
Concrete Slab-Type Elements Strengthened with Cast-in-Place Carbon Textile Reinforced Concrete System

Hyeong-Yeol Kim,Young-Jun You,Gum-Sung Ryu,Gi-Hong Ahn,Kyung-Taek Koh

DOI: https://doi.org/10.3390/ma14061437

2021-03-16

Abstract:Although carbon textile reinforcement widely used to replace the steel reinforcing bars but the bonding strength of carbon textile is generally much smaller than that of common steel bars. This study examines the strengthening effect of concrete slab-type elements strengthened in flexure by carbon textile reinforcement according to the surface coating of textile and the amount of reinforcement. The effect of the surface coating of textile on the bond strength was evaluated through a direct pullout test with four different sizes of coating material. The surface coated specimens developed bond strength approximately twice that of the uncoated specimen. The flexural strengthening effect with respect to the amount of reinforcement was investigated by a series of flexural failure tests on full-scale reinforced concrete (RC) slab specimens strengthened by textile reinforced concrete (TRC) system. The flexural failure test results revealed that the TRC system-strengthened specimens develop load-carrying capacity that is improved to at least 150% compared to the non-strengthened specimen. The strengthening performance was not significantly influenced by the textile coating and was not proportional to the amount of reinforcement when this amount was increased, owing to the change in the failure mode. The outstanding constructability afforded by TRC strengthening was verified through field applications executing TRC strengthening by shotcreting on a concrete box culvert.

Study on Self-compacting Concrete of Textile Reinforced Concrete

Compressive Behavior of GFRP Tubes Filled with Self-Compacting Concrete

Bond Investigation Of Hybrid Textile With Self-Compacting Fine-Grain Concrete

A Study on Thin Concrete Plate Reinforced with Textile

Self-Compacting Concrete For Textile Reinforced Elements

Bond Properties and Experimental Methods of Textile Reinforced Concrete

Investigation on the flexural behavior of reinforced concrete beam strengthened with textile-reinforced concrete

Experimental study on mechanical properties of Textile Reinforced Concrete (TRC)

Mechanical properties research of textile reinforced concrete

Improved Mechanical Properties of Textile Reinforced Concrete Thin Plate

Investigation on the Flexural Behavior of Concrete Members Reinforced with Epoxy Resin-Impregnated Textiles

Experimental Study of Uniaxial Compression Properties of High Performance Fine Grained Concrete

An Experimental Study on Improved Mechanical Behavior of Textile-Reinforced Concrete

An Investigation on Flexural Behavior of Reinforced Concrete Beam with Textile

Experimental Study on Mechanicial Properties of TRC Plate

Mechanical Properties and Durability of Textile Reinforced Concrete (TRC)-A Review

Mechanical properties of textile reinforced concrete plate at low textile ratios

Investigation on Bonding and Overlapping Performance of Textile in Fine Grained Concrete

Analytical Theory of Flexural Behavior of Concrete Beam Reinforced with Textile-Combined Steel

An experimental study on the flexural properties of carbon textile reinforced ECC

Concrete Slab-Type Elements Strengthened with Cast-in-Place Carbon Textile Reinforced Concrete System