Secondary Electron Emission from Reo-Mo Metal Cermet Cathode

Wei Liu,Jinshu Wang,Meiling Zhou

DOI: https://doi.org/10.1109/ivelec.2006.1666218

2006-01-01

Abstract:The secondary electron emission of REO-Mo metal cermet cathodes have been investigated in this paper. The enhancement of Secondary emission yields is related to the annealing technology, which leads to the improvement of the supplement of electron.

What problem does this paper attempt to address?

Study on the secondary electron emission of rare earth-molybdenum cathodes

Wei Liu,Jinshu Wang,Fei Gao,Zhiyuan Ren,Meiling Zhou

2011-01-01

Rare Metal Materials and Engineering

Abstract:The rare earth oxides (REO) doped molybdenum powder was prepared by solid-solid doping, solid-liquid doping and liquid-liquid doping, respectively; afterwards, the powder was sintered by spark plasma sintering and traditional sintering combined with cold isostatic compaction method for fabricating REO-Mo cermet cathodes. OM and emission property tests were used to research the microstructure and the secondary electron emission properties of the samples. The results show that the emission properties of the material can be enhanced through the uniform distribution of rare earth oxides and the refinement of structure. The activation temperature can be decreased greatly by annealing in hydrogen at high temperature, and the secondary emission yield is also enhanced apparently.
Study on the RE2O3-Mo Secondary Electron Emitters

Wei Liu,Jin Shu Wang,Fei Gao,Na Li,Hong Yi Li,Mei Ling Zhou,Tie Yong Zuo

DOI: https://doi.org/10.4028/www.scientific.net/ssp.147-149.845

2009-01-01

Solid State Phenomena

Abstract:A systematic investigation of the fabrication process, microstructure and treatment technology of the Rare earth oxide doped Mo cermet (REO-Mo in brief) on the secondary electron emission (SEE) mainly has been performed. The REO-Mo samples were fabricated by liquid-liquid, Liquid-Solid and Liquid-Liquid doping method and subsequently by the Spark Plasma Sintering (SPS) techniques. It was found that the uniform mixing of REO with Mo would have considerable benefit for enhancement of SEE coefficient (δ). Annealing the cathode in hydrogen (called as the pre-activation treatment) could greatly improve the SEE performance by removing the absorbed water and oxygen at the cathode surface which might cause the oxidation of molybdenum during cathode high temperature operation. It is found that the activation temperature of REO-Mo cathode annealed in hydrogen could decrease to 1000oC, about 300oC lower than that of the cathode without pre-activation treatment, which is favorable for the practical application.
Study on the RE2O3-Mo Secondary Electron Emitters

Wei Liu,Jin Shu Wang,Fei Gao,n l li,Hong Yi Li,Mei Ling Zhou,Tie Yong Zuo

DOI: https://doi.org/10.4028/www.scientific.net/SSP.147-149.845

2009-01-01

Solid State Phenomena

Abstract:A systematic investigation of the fabrication process, microstructure and treatment technology of the Rare earth oxide doped Mo cermet (REO-Mo in brief) on the secondary electron emission (SEE) mainly has been performed. The REO-Mo samples were fabricated by liquid-liquid, Liquid-Solid and Liquid-Liquid doping method and subsequently by the Spark Plasma Sintering (SPS) techniques. It was found that the uniform mixing of REO with Mo would have considerable benefit for enhancement of SEE coefficient (delta). Annealing the cathode in hydrogen (called as the pre-activation treatment) could greatly improve the SEE performance by removing the absorbed water and oxygen at the cathode surface which might cause the oxidation of molybdenum during cathode high temperature operation. It is found that the activation temperature of REO-Mo cathode annealed in hydrogen could decrease to 1000 degrees C, about 300 degrees C lower than that of the cathode without pre-activation treatment, which is favorable for the practical application.
Secondary Electron Emission Property of Composite REO-Mo Materials

刘伟,王金淑,高非,任志远,周美玲

DOI: https://doi.org/10.3321/j.issn:1004-0609.2009.09.017

2009-01-01

Abstract:The sol-gel doping method was utilized to dope the rare earth oxide powder into molybdenum.Such powders were sintered by spark plasma sintering and traditional sintering combined with compaction method for fabricating REO-Mo cermet cathodes.SEM, DTA and electron emission property measurements were used to investigate the secondary electron emission properties of the materials.The results show that the emission performance of the materials can be enhanced by symmetrical distribution of rare earth oxides and the refinement of structure.However, such treatments can't reduce the activation temperature in vacuum.Compared with the un-treated samples, the obvious drop of activation temperature and increase of secondary electron yield occur in samples annealed at high temperature in hydrogen.The activation temperature decreases obviously, and the secondary electron emission yield is enhanced apparently.Such easy adsorption of moisture and gas in the REO lead to oxidation phenomena of molybdenum in the subsequent activation in vacuum.The hydrogen annealing technology eliminates the excess moisture and gas and retain the distribution of REO in molybdenum.This is the main reason of variation of secondary electron emission for un-treated samples and pre-activating samples.
Secondary electron emission of Y2O3–Mo cermet cathode

Jinshu Wang,Wei Liu,Zhiyuan Ren,Fan Yang,Yiman Wang,Meiling Zhou

DOI: https://doi.org/10.1016/j.materresbull.2009.12.004

IF: 5.6

2010-01-01

Materials Research Bulletin

Abstract:Y2O3–Mo cermet cathodes were prepared by mechanical mixing of Y2O3 and Mo powder. The prepared cermet cathode provides a certain secondary emission yield (3.09), about 1.8 times lower than that for the cathode prepared by sol–gel method. It was found that the cathode prepared by sol–gel method had a smaller grain size, which could be attributed to its higher emission property. The energy distributions of primary electrons in the cathodes with different grain sizes have been simulated by Monte Carlo method. Based on the calculation results, the emission models of the cathodes are established and presented. The cathodes with different grain sizes exhibited different ways of emission. Two types of emission, of reflection emission and transmission emission, existed in the cathode with small grain sizes whereas only transmission emission existed in the cathode with large grain sizes.
Secondary emission properties of Mo cathode doped with RE oxides and Re

杨飒,周美玲,王金淑,李洪义,张久兴

DOI: https://doi.org/10.3321/j.issn:1004-0609.2004.01.004

2004-01-01

The Chinese Journal of Nonferrous Metals

Abstract:Properties of secondary emission and atmosphere exposure characteristic for molybdenum cathode doped with rare earth(RE) oxides and Re were investigated. Microstructures of the sinter were analyzed using SEM, and compared with one of molybdenum cathode doped with different RE oxides sinter. The results show that the secondary emission coefficient of the RE-Mo sinter can be increased by 8%. The maximum secondary emission coefficient(δ_m) is 2.65. The emitter possesses the better property of exposition in atmosphere.
Study on Rare Earth Oxide-Molybdenum Cermet Cathode Materials

JS Wang,HY Li,S Yang,YQ Liu,ML Zhou

DOI: https://doi.org/10.1016/j.jallcom.2004.03.135

IF: 6.2

2004-01-01

Journal of Alloys and Compounds

Abstract:The emission property of a new kind of rare earth oxide–molybdenum cermet cathode made by powder metallurgy has been studied in this paper. The experimental results show that adding either single rare earth oxides La2O3, Y2O3, and Gd2O3 or a mixture of these rare earth oxides into molybdenum can improve the secondary emission coefficient of the cathode. After La2O3–Y2O3–Gd2O3–Mo is activated at 1600°C, the maximum secondary emission coefficient can be high to more than 3.0. This kind of cathode also shows good secondary emission stability during 1000h of life experiment and capability of anti-exposure to atmosphere. The zero-field emission density of 0.12A/cm2 is reached at 1470°C.
Characteristics of La2O3–Y2O3–Mo cermet cathode with RE2O3 nano particles

Jinshu Wang,Wei Liu,Zhiyuan Ren,Fan Yang,Yiman Wang,Yucheng Du,Meiling Zhou

DOI: https://doi.org/10.1016/j.cap.2010.11.014

IF: 2.856

2011-01-01

Current Applied Physics

Abstract:The secondary electron emission property and microstructure of La2O3–Y2O3–Mo cermet cathode have been studied. It shows that the cathode prepared by Sol–Gel doping method has fine microstructure containing rare earth oxide (RE2O3) nanoparticles and uniform distribution of different substances. Auger Electron Spectroscopy (AES) depth profile result shows that an RE2O3 layer about 28 nm in thickness could be formed on the cathode surface, which plays an important role in the emission. Pre-activation of the cathode is favorable for the improvement of emission property. La2O3–Y2O3–Mo cathode pre-activated exhibits good secondary emission property. The secondary emission yield could reach 5.24, about 1.8 times higher than that of original cathode. The enhancement on the conductivity of materials resulting from the pre-activation is favorable for the replenishment and transport of electrons, thus the secondary emission property of the cathode could be improved.
Secondary Emission Property of CeO2-Y2O3-Mo Cathode

Jinshu Wang,Wei Liu,Fei Gao,Yiman Wang,Meiling Zhou

DOI: https://doi.org/10.1109/ivelec.2007.4283273

2007-01-01

Abstract:Secondary emission has been used in many fields stimulated by the development of vacuum electronic technology, especially in the field of high power magnetron. The development of high power magnetron needs cathodes which could provide high secondary emission yield (Vasilyva, 1996). As a novel cathode which is expected to be applied in magnetron, CeO2-Y2O3-Mo cermet cathode has be prepared by liquid-liquid doping combined with a fast sintering, spark plasma sintering technique.
Recent progress of rare earth oxide doped Molybdenum secondary electron emission cathodes

Wei Liu,Jinshu Wang,Zhiyuan Ren,Fengtao Gao,Meiling Zhou

DOI: https://doi.org/10.1109/IVESC.2010.5644445

2010-01-01

Abstract:In this paper, the effect of different preparation process on the secondary electron emission performance was investigated. The different doping methods and preparation techniques such as Solid-Solid doping(SS), Liquid-Solid (LS) doping, Liquid-Liquid (LL) doping, Spark Plasma Sintering (SPS), Air Plasma Spray (APS) method, were introduced into this kind of materials. The microstructure of samples was observed with Hitachi S-3500N Scanning Electron Microscopy, equipped with Oxford Inca EDX equipment. The self-designed apparatus was used to evaluate secondary electron emission yields (δ) of samples in the ultra-high vacuum chamber. The secondary emission properties were measured at 600°C in order to avoid the influence of the thermionic emission.
Preparation and Characterization of Single RE2O3–Mo Secondary Emission Materials

Jinshu Wang,Wei Liu,Fei Gao,Zhiyuan Ren,Meiling Zhou

DOI: https://doi.org/10.1016/j.solidstatesciences.2008.04.012

IF: 3.752

2008-01-01

Solid State Sciences

Abstract:La2O3–Mo, Y2O3–Mo, Gd2O3–Mo and Ce2O3–Mo were prepared by liquid–liquid doping combined with spark plasma sintering. The microstructure and surface behaviour of rare earth oxide of the cathode have been studied by microscope, Auger Electron Spectroscopy (AES) and X-ray Photoelectron Spectroscopy (XPS) methods. Among these four kinds of cathode, Y2O3–Mo cathode exhibits the best secondary emission property, i.e., the maximum secondary emission yield could reach 5.24. The penetration depth of primary electrons and escape depth of secondary electrons have been calculated and the energy distribution of primary electrons in the cathode has been simulated by Monte Carlo method. Y2O3–Mo cathode has the largest penetration depth and escape depth, which could be attributed to the highest secondary electron emission yield of the cathode.
Recent Progress on RE2O3-Mo/W Emission Materials

Jinshu Wang,Xizhu Zhang,Wei Liu,Yuntao Cui,Yiman Wang,Meiling Zhou

DOI: https://doi.org/10.1109/ivesc.2010.5644350

2012-01-01

Journal of Nanoscience and Nanotechnology

Abstract:With the rapid development of broadcasting, communication and aviation industry, the study of vacuum electron devices has become the key issue of the researchers around the world. Being the heart of electron tubes and magnetrons, the cathode plays an important role in these devices. Two kinds of cathodes, rare earth oxide-Mo cermet (RE2O3-Mo in brief) secondary emission materials and Scandia doped tungsten matrix impregnated thermionic emission materials have been studied.
Secondary Emission Property of Y2O3-Lu2O3-Mo Cathode

Jinshu Wang,Wei Liu,Fei Gao,Yiman Wang

DOI: https://doi.org/10.1109/ivelec.2008.4556347

2008-01-01

Abstract:A RE2O3-Mo cathode which contains Lu2O3 and Y2O3 with a certain weight ratio was made using a Sol-Gel technique and the spark plasma sintering technique. The maximum secondary emission yield (deltam) of this cathode could reach 4.6 while the activation temperature is only 900degC.
Durability Experiment on Anti-Electron-Bombardment of Re2o3-Mo Secondary Emission Material

S Yang,JS Wang,ML Zhou,YJ Gao,HY Li

IF: 3.752

2004-01-01

Transactions of Nonferrous Metals Society of China

Abstract:A durability test to determine anti-bombardment sensitivity of multi-RE2 O3-Mo secondary emission material was carried out and the variation of maximum secondary emission coefficient (δmax) was monitored at regular intervals. After the experiment, the cathode was analyzed with SEM, EDS and XRD techniques. The results show that δmax of multi-RE2O3-Mo cermets cathode heated to 1 100 ℃ under electron bombardment of 300 W/cm2 reaches the peak of 3.35 at 200 h. After 500 h of bombardment, the maximum secondary-electron-yield curve stabilizes. The δmax value of the cathode remains at about 2.5 after 1 000 h and represents a good anti-bombardment property. The high δmax value of the cathode is related with formation of an enriched Y2 O3 layer on the surface under high temperature and with the amount of La2 O3 particles in the shape of nanometer distributed on the surface. Under the experimental conditions, the drop of δmax value may be caused by the reduction of La2 O3 content and the porous layer resulted from evaporation of MoO2, which is formed when Mo at the surface is oxidized.
Emission property of RE2O3 doped Mo cathode materials

Jinshu Wang,Wei Liu,Fei Gao,Yiman Wang,Meiling Zhou

DOI: https://doi.org/10.1109/IVELEC.2007.4283307

2007-01-01

Abstract:Single La 2 O 3 , Ce 2 O 3 doped Mo with low content of RE 2 O 3 has good thermionic emission property. The zero-field emission current densities at 1450 degC of 6.87A/cm and 5.03 A/cm2 could be obtained for La 2 O 3 (4wt%)-Mo and Ce203(4wt%)-Mo, respectively.La 2 O 3 -Mo, Ce 2 O 3 -Mo cermet cathode containing high content of RE 2 O 3 shows a certain secondary emission property. A layer of RE 2 O 3 could be formed at surface of the cathode and plays an important role in the emission.
A Study of Emission Property and Microstructure of Rare Earth Oxide–molybdenum Cermet Cathode Materials Made by Spark Plasma Sintering

JS Wang,HY Li,S Yang,Y Cui,ML Zhou

DOI: https://doi.org/10.1016/j.jallcom.2004.02.046

IF: 6.2

2004-01-01

Journal of Alloys and Compounds

Abstract:A fast sintering method, spark plasma sintering (SPS) was used for the synthesis of rare earth oxide–molybdenum cathode material. The secondary emission property, microstructure, and phase constitution of materials have been studied in this paper. The experimental results show that the maximum secondary emission coefficient of this material can be high to 3.84, much higher than that of rare earth oxide–molybdenum cathode made by traditional sintering method. The grain size is less than 1μm and rare earth distributed evenly in the material. After the material was activated at 1600°C, a 4μm layer of rare earth oxide which leads to the high secondary emission coefficient of the material, is formed on the surface of the cathode.
Advances in Rare Earth Doped Refractory Metal Cathode Materials

WANG Jin-shu,LIU Wei,LI Na,GU Xin,WANG Yi-man,LI Ji

DOI: https://doi.org/10.3969/j.issn.1002-8935.2006.02.002

2006-01-01

Abstract:The thermionic emission properties of rare earth doped molybdenum cathode and impregnated cathode with sub-micron scandia doped tungsten matrix,and the secondary emission property of rare earth doped molybdenum cathode have been studied in this paper.It was shown that La_2O_3-Mo cathode had good thermionic emission property and the capability of anti-exposition to the atmosphere.The maximum secondary emission coefficient of the rare earth doped molybdenum cathodes activated at 1000～1200 ℃ could exceed 4.0.The impregnated cathodes with submicron scandia doped tungsten matrix exhibited excellent emission property.The current densities of more than 30 A/cm~2 at 850℃_b could be obtained,and the emission homogeneity was improved with the ordinary scandate cathode.
A Study on La2O3-Y2O3-Mo Secondary Emission Material

JS Wang,J Liu,ML Zhou,HY Li,JX Zhang,TY Zuo

2003-01-01

Abstract:The substrate molybdenum doped with La2O3, Y2O3 cathode material was made by the powder metallurgy method. The secondary emission coefficients of them aterials were tested. The experimental results show that Mocathodes doped with La2O3,Y2O3 have good secondary emission properties. When the cathodes are activated, the maximal secondary emission coefficients of these cathodes are higher than 2.0 and can meet the practical requirement. The distribution of the rare earth in the interior and at surface of this kind of cathode material before and after emission was studied using Scanning Electronic Microscopic (SEM) and X -Ray Photoelectron Spectrum(XPS). The analysis results show that the rare earth is easy to gather at grain boundaries and the relevant concentration of rare earth on the surface after emission is obviously greater than that before emission .
P1–30: Fabrication of Y2O3-Mo secondary electron emitters by air Plasma Spray method

Wei Liu,Jinshu Wang,Zhiyuan Ren,Fan Yang,Meiling Zhou,Tieyong Zuo

DOI: https://doi.org/10.1109/IVELEC.2010.5503553

2010-01-01

Abstract:Rare earth oxide (REO) doped Molybdenum metal ceramic emitters were successfully prepared by the air Plasma Spray (APS) method. Microstructure and secondary electron emission (SEE) performance were investigated. The relative uniform mixing of rare earth oxide and molybdenum have been observed. The maximum secondary electron yield is 3.3 after activation at 1100b(Mo brightness temperature) in vacuum.
Enhancement of Secondary Emission Property of Molybdenum Cathode Co-Doped with La2o3 and Y2o3

Wang Jinshu,Liu Wei,Ren Zhiyuan,Yang Fan,Gao Fei,Zhou Meiling

DOI: https://doi.org/10.1016/s1002-0721(08)60373-7

IF: 4.632

2009-01-01

Journal of Rare Earths

Abstract:La2O3 and Y2O3 co-doped Mo secondary emitters were prepared by three kinds of doping method combined with high temperature plasma sintering. The secondary electron emission property and microstructure of the cathodes were studied. It showed that the cathode prepared by liquid-liquid doping method exhibited the best emission property among all the samples prepared by liquid-solid doping, solid-solid doping and liquid-liquid doping methods due to a uniform distribution of different substances. RE2O3 existed uniformly at the grain boundaries and diffused to the cathode surface during a cathode activation period. A surface layer of RE2O3 formed after activation played an important role in the emission. The secondary emission yield of La2O3 and Y2O3 co-doped Mo prepared by liquid-liquid doping method was 4.34.

Secondary Electron Emission from Reo-Mo Metal Cermet Cathode

Study on the secondary electron emission of rare earth-molybdenum cathodes

Study on the RE<sub>2</sub>O<sub>3</sub>-Mo Secondary Electron Emitters

Study on the RE<sub>2</sub>O<sub>3</sub>-Mo Secondary Electron Emitters

Secondary Electron Emission Property of Composite REO-Mo Materials

Secondary electron emission of Y2O3–Mo cermet cathode

Secondary emission properties of Mo cathode doped with RE oxides and Re

Study on Rare Earth Oxide-Molybdenum Cermet Cathode Materials

Characteristics of La2O3–Y2O3–Mo cermet cathode with RE2O3 nano particles

Secondary Emission Property of CeO2-Y2O3-Mo Cathode

Recent progress of rare earth oxide doped Molybdenum secondary electron emission cathodes

Preparation and Characterization of Single RE2O3–Mo Secondary Emission Materials

Recent Progress on RE2O3-Mo/W Emission Materials

Secondary Emission Property of Y2O3-Lu2O3-Mo Cathode

Durability Experiment on Anti-Electron-Bombardment of Re2o3-Mo Secondary Emission Material

Emission property of RE2O3 doped Mo cathode materials

A Study of Emission Property and Microstructure of Rare Earth Oxide–molybdenum Cermet Cathode Materials Made by Spark Plasma Sintering

Advances in Rare Earth Doped Refractory Metal Cathode Materials

A Study on La2O3-Y2O3-Mo Secondary Emission Material

P1–30: Fabrication of Y2O3-Mo secondary electron emitters by air Plasma Spray method

Enhancement of Secondary Emission Property of Molybdenum Cathode Co-Doped with La2o3 and Y2o3

Secondary Electron Emission from Reo-Mo Metal Cermet Cathode

Study on the secondary electron emission of rare earth-molybdenum cathodes

Study on the RE&lt;sub&gt;2&lt;/sub&gt;O&lt;sub&gt;3&lt;/sub&gt;-Mo Secondary Electron Emitters

Study on the RE<sub>2</sub>O<sub>3</sub>-Mo Secondary Electron Emitters

Secondary Electron Emission Property of Composite REO-Mo Materials

Secondary electron emission of Y2O3–Mo cermet cathode

Secondary emission properties of Mo cathode doped with RE oxides and Re

Study on Rare Earth Oxide-Molybdenum Cermet Cathode Materials

Characteristics of La2O3–Y2O3–Mo cermet cathode with RE2O3 nano particles

Secondary Emission Property of CeO2-Y2O3-Mo Cathode

Recent progress of rare earth oxide doped Molybdenum secondary electron emission cathodes

Preparation and Characterization of Single RE2O3–Mo Secondary Emission Materials

Recent Progress on RE2O3-Mo/W Emission Materials

Secondary Emission Property of Y2O3-Lu2O3-Mo Cathode

Durability Experiment on Anti-Electron-Bombardment of Re2o3-Mo Secondary Emission Material

Emission property of RE2O3 doped Mo cathode materials

A Study of Emission Property and Microstructure of Rare Earth Oxide–molybdenum Cermet Cathode Materials Made by Spark Plasma Sintering

Advances in Rare Earth Doped Refractory Metal Cathode Materials

A Study on La2O3-Y2O3-Mo Secondary Emission Material

P1–30: Fabrication of Y2O3-Mo secondary electron emitters by air Plasma Spray method

Enhancement of Secondary Emission Property of Molybdenum Cathode Co-Doped with La2o3 and Y2o3

Study on the RE<sub>2</sub>O<sub>3</sub>-Mo Secondary Electron Emitters