Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

Refinement mechanism of trace Sc and Zr as-cast 7A55 alloys

Refinement Mechanism of Trace Cr, Mn, Ti and Zr As Cast 7A55 Alloys

Research on Grain Refinement of Sc and Zr Addition in an Al-Mg-Zn Alloy from Experiments and First-Principles Calculations

Effect of Sc and Zr on Microstructure and Mechanical Properties of As‐Cast Al–Li–Cu Alloys

Effect of Trace Zr on Microstructure and Hardness of Al-Zn-Mg-Cu Alloy Prepared under Supergravity

Influence of minor Sc additions on grain refinement and microstructure characteristics of a high Zn-containing Al-Zn-Mg-Cu-Zr alloy

Effects of Sc and Zr microalloying on the microstructure and mechanical properties of high Cu content 7xxx Al alloy

An experimental study of the effect of Ag, Cu, Li, Mg, Ni, Ti, Sc, Zr on grain refining in binary and multicomponent Al-based alloys

Study on Grain Refining and Metamorphism of ZL111 Aluminium Alloys

In Situ Radiographic Study of the Grain Refining Behavior of Al3Sc During the Solidification of Al-10Cu Alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

In situ radiographic study of the grain refining behavior of Al3Sc during the solidification of Al-1OCu alloy

Effect of Scandium on Grain refinement mechanism and Mechanical Properties of Al-7Si-0.6Mg alloy at Different Cooling Rates

Effects of Sc Addition on the Microstructure and Mechanical Properties of Cast Al-3Li-1.5Cu-0.15Zr Alloy

Effect of Zr Microalloying on the Microstructures and Strengthening Mechanism of As-Cast Al-Fe-Zr Alloys

Modification Mechanism And Growth Process Of Al-3(Sc, Zr) Particles In As-Cast Al-Si-Mg-Cu-Zr-Sc Alloy

Effect of Zr and Sc Micro-Additions on the Microstructure and Mechanical Properties of As-Cast Al-5Ce Alloy

Microstructures and Properties of Al–Zn–Mg–Mn Alloy with Trace Amounts of Sc and Zr

Effect of Sc/Zr ratio on the microstructure and mechanical properties of new type of Al–Zn–Mg–Sc–Zr alloys

Influence of Sc Content on the Microstructure and Mechanical Properties of Cast Al-2Li-2Cu-0.5Mg-0.2Zr Alloy

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy