Abstract:In this study, the metallurgical mechanisms of inclusions during electron beam smelting (EBS) of a FGH4096 powder superalloy was investigated. The macroscopic morphology of the ingots, as well as the composition and structure of inclusions were studied. The effect of electron beam smelting parameters on the cooling rate, O/N content, number density and size of inclusions have been revealed. Besides, the mechanisms for inclusions removal and formation were elucidated. The results show that inclusions in the final solidification zone are mainly oxides (simple tetragonal CrO 2 , hexagonal Al 2 O 3 , and face-centered cube TiN), whereas the complex inclusions and carbon nitrides with Al 2 O 3 and TiN as the nucleation cores are mainly present in the matrix. With the increase in smelting power and time, both the cooling rate and O/N content decsrease, and the smelting power shows a greater impact on the cooling rate. The number density of total inclusions increases with the increase in the smelting power. As the smelting time increases, the number density of total inclusions decreases, while the size of complex inclusions and carbon nitrides increases. This is attributed to the combined effect of cooling rate and O/N concentration in the alloy under different smelting parameters. Thermodynamic calculations indicate that Al 2 O 3 forms in the solid-liquid phase region. The precipitation of TiN occurs when the alloy solidifies, and its precipitation temperature is higher than that of TiC. The lattice mismatch between Al 2 O 3 and TiN is 8.14%, while that between TiC and TiN is 6.94%, which effectively promotes the heterogeneous nucleation of complex inclusions and carbon nitrides. The formation mechanisms of complex inclusions and carbon nitrides provide a theoretical basis for purification of superalloys by electron beam metallurgy.

Discussions on Nucleation Mechanism of Intragranular Ferrite in Inclusions

The Mechanism of Intragranular Ferrite Nucleation on Inclusion in Steel

Kinetics and Mechanisms of Intragranular Ferrite Nucleation on Non-Metallic Inclusions in Low Carbon Steels

Discussing mechanisms of nitrogen removal during ferritic stainless steelmaking

Study on Three-Dimensional Morphology of Intragranular Nucleating Ferrites in Low Carbon Steels

Influence of Inclusions on the Nucleation of Acicular Ferrites in a Ti–Zr‐Bearing Steel

Ferrite Formation Dynamics and Microstructure Due to Inclusion Engineering in Low-Alloy Steels by Ti2O3 and TiN Addition

Study of thermal stress and strain energy in gamma Fe matrix around inclusion caused by thermal coefficient difference

Discussion On The Nucleation Rate Of Ferrite During Continuous Cooling In A Lowcarbon Steel Measured By 3dxrd

Influence of Prior Austenite Deformation and Non-Metallic Inclusions on Ferrite Formation in Low-Carbon Steels

Influence of TiO2 on Intragranular Acicular Ferrite Nucleation in Low-Carbon Steel

Effects of Microstructure on the Temperature Dependence of Relative Initial Permeability of NiCuZn Ferrites

Migration Behavior of Inclusions at the Solidification Front in Oxide Metallurgy

Phase field simulation of nucleation of solid-solid phase transformation in multiple phase transition

Effect of inclusions on toughness and microstructures in simulated coarse-grain heat-affected zones of Al/Ti deoxidised and Nb/V microalloyed steels

Effect of Al Content on the Agglomeration Behavior of Inclusions in High Al Steel

An Investigation of Nucleation Sites for the Formation of Solute Clusters in Ferrite Fe

Study on the metallurgical mechanisms of inclusions in the FGH4096 alloy during electron beam smelting

Study on the mechanism of AF nucleation induced by complex oxide inclusions after LF refining in oxide metallurgical steel

Characterization of strain induced ferrite formed in coarse austenite grained Q235 steel

Nucleation and growth mechanisms of ferrite on Mg-Ti-oxide surfaces: First-principles investigation