Abstract:A new jet fuel surrogate was developed in this work by emulating real jet fuel properties including physical, gas phase chemical properties and threshold sooting index (TSI). An intelligent optimization methodology was proposed to calculate the species composition that inherently satisfies both the physical and chemical characteristics as well as sooting tendency. Eight properties were selected as the target properties for the jet fuel surrogate development, including liquid density, viscosity, surface tension, cetane number (CN), hydrogen carbon (H/C) ratio, molecular weight (MW), lower heating value (LHV) and TSI. As a result, the CN, H/C ratio, LHV, TSI and density of the new jet fuel surrogate are reproduced excellently with very little deviations within 3%. The averaged deviation of viscosity is −6.318% and the deviations of MW is 9.776%. As the highest deviation among all properties, the averaged deviation of surface tension is 11.76%. Based on the newly developed jet fuel surrogate, a skeletal jet fuel surrogate mechanism with 5 components including decalin, n-dodecane, iso-cetane, iso-octane and toluene was developed. The skeletal jet fuel surrogate mechanism was significantly compacted into 74 species and 189 reactions by describing the chemistries for the oxidation of large molecules C4–Cn and small H2/CO/C1 molecules respectively, which makes it practical to be used for 3-D engine combustion simulations. The validations of ignition delay times present reasonable agreement between experiment and predictions over a wide range of equivalence ratios (0.5–2.0) and pressures (8–30 atm), except for a shift of negative temperature coefficient (NTC) region towards higher temperatures at Φ = 1.5, 20 atm: in the simulation the NTC region is from 830 K to 950 K while in the experiment the NTC region is from 740 K to 890 K. The predicted species concentrations can reproduce the trend of the experimental data, especially for O2, CO and CO2. The simulated laminar flame speed at 400 K and 470 K are with absolute averaged deviations of 3.5% and 4.06% respectively. The constant volume spray and combustion validations are reasonably good. In the engine combustion validations, a multistep soot model was embedded into the new jet fuel surrogate mechanism. The predicted in-cylinder pressure can reproduce the experimental data, expect for small deviations after the peak pressure (the averaged deviation is around 6.2% after the peak pressure). The embedded soot model can well reproduce the trend of the experimental data. It can be concluded that this new jet fuel surrogate mechanism is compact and robust for the utilization in diesel engine combustion simulation.

Combustion Flow of Kerosene-Fueled Scramjet with 3D Cavity (Ⅲ) Multi-step Chemistry Characteristics of Kerosene

Numerical Investigation on Combustion Flow of a Kerosene-Fueled Scramjet with 3D Cavity(ⅱ) Preliminary Investigation on Fuel/air Mixing and Flame Stabilization Enhanced by 3D Cavity

A Direct Numerical Simulation Study of Flame Structure and Stabilization of an Experimental High Ka CH4/air Premixed Jet Flame

Direct Numerical Simulation of a High Ka CH4/air Stratified Premixed Jet Flame

Numerical Investigation on Two Phase Flow of a Kerosene-Fueled Scramjet with 3D Cavity(ⅰ) Numerical Calibration and Characteristics of General Flow

Numerical study on the mixing and combustion characteristics of a liquid kerosene jet in a scramjet combustor

Aviation kerosene supersonic combustion in dual-mode scramjet

Improved delayed detached eddy simulation of supersonic combustion fueled by liquid kerosene

Numerical Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Consideration of Fuel Pyrolysis and Surface Coking at Supercritical Pressures

Effect of kerosene injection states on mixing and combustion characteristics in a cavity-based supersonic combustor

Modeling of Supercritical-Pressure Turbulent Combustion of Hydrocarbon Fuels Using A Modified Flamelet-Progress-Variable Approach

Numerical study on ignition of supersonic combustion fueled by partly catalyzed kerosene

Numerical study on the mixing and evaporation process of a liquid kerosene jet in a scramjet combustor

Effect of cavity arrangement on the ignition mode of vaporized kerosene in supersonic flow

Effect of fuel temperature on mixing characteristics of a kerosene jet injected into a cavity-based supersonic combustor

Effects of Kerosene Global Reaction Mechanisms on Supersonic Combustion

Development of a New Jet Fuel Surrogate and Its Associated Reaction Mechanism Coupled with a Multistep Soot Model for Diesel Engine Combustion

Modeling and Simulation of Supercritical-Pressure Turbulent Heat Transfer of Aviation Kerosene with Detailed Pyrolytic Chemical Reactions

Computational Study of the Effect of Dual Air Swirling Injection on Turbulent Combustion of Kerosene–Air at a High Pressure

Large Eddy Simulations of Turbulent Combustion of Kerosene-Air in a Dual Swirl Gas Turbine Model Combustor at High Pressures

Investigation of Unsteady Combustion Regimes in a Kerosene-Fueled Scramjet with Air Throttling