Abstract:The friction and wear properties of the polyetheretherketone (PEEK) based composites filled with 5 mass% nanometer or micron Al2O3 with or without 10 mass% polytetrafluroethylene (PTFE) against the medium carbon steel (AISI 1045 steel) ring under the dry sliding condition at Amsler wear tester were examined. A constant sliding velocity of 0.42ms−1 and a load of 196 N were used in all experiments. The average diameter 250μm PEEK powders, the 15 or 90nm Al2O3 nano-particles or 500nm Al2O3 particles and/or the PTFE fine powders of diameter 50μm were mechanically mixed in alcohol, and then the block composite specimens were prepared by the heat compression moulding. The homogeneously dispersion of the Al2O3 nano-particles in PEEK matrix of the prepared composites was analyzed by the atomic force microscopy (AFM). The wear testing results showed that nanometer and micron Al2O3 reduced the wear coefficient of PEEK composites without PTFE effectively, but not reduced the friction coefficient. The filling of 10 mass% PTFE into pure PEEK resulted in a decrease of the friction coefficient and the wear coefficient of the filled composite simultaneously. However, when 10 mass% PTFE was filled into Al2O3/ PEEK composites, the friction coefficient was decreased and the wear coefficient increased. The worn scars on the tested composite specimen surfaces and steel ring surfaces were observed by scanning electron microscopy (SEM). A thin, uniform, and tenacious transferred film on the surface of the steel rings against the PEEK composites filled with 5 mass% 15nm Al2O3 particles but without PTFE was formed. The components of the transferred films were detected by energy dispersive spectrometry (EDS). The results indicated that the nanometer Al2O3 as the filler, together with PEEK matrix, transferred to the counterpart ring surface during the sliding friction and wear. Therefore, the ability of Al2O3 to improve the wear resistant behaviors is closely related to the ability to improve the characteristics of the transfer film.

Abrasive wear characteristics and mechanisms of A12O3/PA1010 composite coatings

Influence of Al2O3 reinforcement on the abrasive wear characteristic of Al2O3/PA1010 composite coatings

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

FABRICATION OF Al2O3/HEAT-RESISTANT STEEL COMPOSITEAND ITS WEAR-RESISTANCE AT HIGH TEMPERATURE AND ABRASIVE

A study on friction and wear characteristics of nanometer Al2O3 /PEEK composites under the dry sliding condition

Research on microstructure, mechanical property and wear mechanism of AlCoCrFeNi/WC composite coating fabricated by HVOF

The Microstructure and Tribological Property of In-Situ Al2O3/Fe–25Al Composites in Argon Atmosphere

Tribological properties of PEEK-based composite coating prepared by thermal spraying

Microstructure and Tribocorrosion Behavior of Al2O3/Al Composite Coatings: Role of Al2O3 Addition

Tribological Properties of in Situ Fe3al-20 Wt% Al2o3 Composites

Comparative Study of Wear Performance of Ceramic/Iron Composite Coatings under Two Different Wear Modes

Fretting wear behaviors of nanometer Al2O3 and SiO2 reinforced PEEK composites

Microstructure and sliding wear behavior of pseudo-alloy PS45/CuAl8 composite coating sprayed by HVAA technique

Tribological Properties of 7A04 Aluminum Alloy Enhanced by Ceramic Coating

Self-Lubricating Al2o3/Ptfe Composite Coating Formation on Surface of Aluminium Alloy

Abrasive Wear Behaviors of High Velocity Arc Sprayed Iron Aluminum Composite Coatings

Effects of nanoceramic particle size and content on the wear resistance of micro-arc oxidation coatings for 2A12 aluminum alloy

A Study of Parameters Affecting Wear Resistance of Alumina and Yttria Stabilized Zirconia Composite Coatings on Al-6061 Substrate

Dry Sliding Wear Behaviour of Al<sub>2</sub>O<sub>3</sub>-Cr<sub>2</sub>O<sub>3</sub> Coatings with Different Contents of Cr<sub>2</sub>O<sub>3</sub>

Elucidation of Abrasive Wear and Slurry Erosion Behavior of Fe Matrix Composites Reinforced with Metallic Coating Modified ZTAP Ceramics

Microstructure evolution and tribological behavior of the laser in-situ synthesized ceramics reinforced CoFH alloy-based composite coating on the 304 stainless steel