Abstract:The conductive nano-Al/polyaniline composites were prepared by the milling method in the solid state. Here, aluminum nanostructures were prepared in two different mechanical methods, wire drawing and wire milling in the presence of lubricant oil. The effects of the preparation methods on the structures and morphologies of aluminum nanostructures were investigated by XRD and FESEM. The results show that the shape and size of aluminum nanoparticles in the preparation by the wire drawing method are significantly different than the wire milling method. The aluminum nanostructures were prepared by milling method have flake-like nanosheets while the wire drawing method leads to the formation of spherical ultrafine nanoparticles, which particles size are in the range of 30–60 nm. Then, polyaniline was produced using a solid-state polymerization process by the chemical reaction between aniline hydrochloride and potassium peroxydisulfate. Finally, nano-Al/polyaniline composites were prepared by mechanical milling at room temperature. The quantitative analysis was carried out with the materials analysis using diffraction (MAUD) method and weight fraction for aluminum and PANI were calculated 6.66% and 93.34%, respectively. Electrical conductivity measurements show the conductivity (1.2 × 10 −2 S cm −1 at 25 °C) for polyaniline emeraldine salt and (1.02 × 10 −3 S cm −1 at 25 °C) in nanocomposite respectively. The results show that by adding aluminum nanoparticles to the polymer the conductivity of nanocomposite (Al/PANI-ES) is lower than that for pure (PANI-ES). Thermogravimetry and differential thermal analysis curves show pure (PANI-ES) and nanocomposite (Al/PANI-ES) have a similar thermal degradation process. The total weight loss in TG curve of pure PANI-ES, in the temperature range 45–800 °C is 46.28% but, total weight loss observed in nanocomposite is 38.67%. Therefore, nanocomposite has higher thermal stability than that of the pure PANI-ES.

Electrical and structural analysis of conductive polyaniline/polyacrylonitrile blends prepared from a chloroform/DMSO mixture

Electrical and Structural Analysis of Conductive Polyaniline/polyacrylonitrile Composites

Relationship Between Electrical Conductivity And Phase Morphology Of Polyaniline/polyacrylonitrile And Polyaniline/polystyrene Blends

Hydrogen Bonding Effects on the Electrical Properties and Phase Morphology of Polyaniline Blends

Electric Conductivity and Thermorheology Properties of Polyacrylonitrile/Nylon6 Composites Filled with Carbon Black

Investigating the electrochemical properties of poly(vinylidene fluoride)/polyaniline blends doped with lithium-based salt

Electrically Conductive PANI-DBSA/Co-PAN Composite Fibers Prepared by Wet Spinning

Improvement of the structural and electrical properties of PMMA/PANI-MA blends synthesized by interfacial in situ polymerization in a continuous organic phase

Structures and properties of the water-soluble self-acid-doped conducting polymer blends: sulfonic acid ring-substituted polyaniline/poly(vinyl alcohol) and poly(aniline-co-N-propanesulfonic acid aniline)/poly(vinyl alcohol)

Design of a Low-Cost PMMA/PVAc/PANI Blended Polymers: Structural, Electrical and Dielectric Characteristics

Conductive Polyaniline Doped with Dodecyl Benzene Sulfonic Acid: Synthesis, Characterization, and Antistatic Application

Characterization Of Pan/Pani-Dbsa Blend Nanofibers Produced By Electrospinning Method

Electronic Transport in Pani-Csa/Pani-Dbsa Polyblends

Preparation and Characterization of Polyaniline/Mmt Conductive Composites

Preparation of the PAn/PMMA Conductive Composite by In-Situ Emulsion Polymerization

Conductive behaviour of lithium ions in polyacrylonitrile

Morphology and conductivity of polyaniline sub-micron fibers prepared by electrospinning

Preparation and Electromagnetic Wave-Absorbing Properties of Micro-Polyaniline/Fe3o4 Hollow Spheres

Conductive nano-Al/polyaniline composites prepared via mechanical milling

Controlling the Structure and Morphology of Monodisperse Polystyrene/Polyaniline Composite Particles

Synthesis and Characterization of Conducting PANDB/χ-Al2O3 Core-Shell Nanocomposites by In Situ Polymerization