Abstract:Despite the unique properties of polyaniline (PANI), the processability of this smart polymer is associated with challenges. Particularly, it is very difficult to prepare PANI nanofibers due to poor solubility, high charge density, and rigid backbone. The most common approach for solving this problem is blending PANI with a carrier polymer. Furthermore, the major limitations of nanofibers for tissue engineering applications are their low porosity and two-dimensional (2D) structure. In this study, conductive nanofibers were fabricated through electrospinning of PANI/poly(ether sulfone) (PES) with different solvents including dimethyl sulfoxide (DMSO), N-methyl-2-pyrrolidone (NMP), and hexafluoroisopropanol (HFIP). The effect of solvent, carrier polymer (PES), and PANI content on formation of 3D conductive nanofibers with appropriate porosity were investigated. It was shown that a solvent with suitable properties should be selected in such a way that the composite nanofibers can be electrospun at the lowest concentration of PES. In this way, the ratio of PANI increased in the scaffold, the electrical conductivity of nanofibers enhanced, and the flat 2D structure of scaffold changed to a fluffy 3D structure. Among the three studied solvents, HFIP with the lowest boiling point and the lowest surface tension was the best solvent for the fabrication of PANI/PES nanofibers. PES could be electrospun at a concentration of 9% w/w in HFIP, while the optimum percentage of PES in DMSO and NMP was above 23% w/w to produce uniform nanofibers. 3D nanofibrous scaffold obtained from 0.5% PANI/9% PES/HFIP solution with electrical conductivity of 3.7 × 10-5 S/Cm and porosity of 92.81 ± 1.23%. Cell infiltration into the 3D nanofibers with low packing density improved compared to densely packed 2D nanofibers.

Morphology and conductivity of polyaniline sub-micron fibers prepared by electrospinning

Preparation of Polyaniline Doped with Acid and Polymer Using Electrochemical Deposition

Polyaniline Nanobelts, Flower-Like and Rhizoid-Like Nanostructures by Electrospinning

Fabrication of one dimensional polyaniline nanofibers by UV-assisted polymerization in the aqueous phase.

Polyaniline Nanofiber Humidity Sensor Prepared by Electrospinning

Electrically Conductive PANI-DBSA/Co-PAN Composite Fibers Prepared by Wet Spinning

Synthesis and Properties of Polyaniline Nanostructures Using Different Ferric Salts

Characterization Of Pan/Pani-Dbsa Blend Nanofibers Produced By Electrospinning Method

Enhancing Cellular Infiltration on Fluffy Polyaniline-Based Electrospun Nanofibers

Effect of polyaniline content and protonating dopants on electroconductive composites

Acid‐doped polyaniline and its vertically aligned SWCNT composites: Influence of acid type and concentration on structural and electrochemical properties

PREPARATION OF POROUS POLYACRYLONITRILE ULTRATHIN FIBERS BY ELECTROSPINNING WITH NONSOLVENT INDUCED PHASE SEPARATION

A Study On The Synthesis, Characterization And Properties Of Polyaniline Nanofibers Using Ferric Chloride As Both Oxidant And Dopant

Electrosynthesis and Characterisation of the Polyaniline Fiber

Wet-Spun Side-by-Side Electrically Conductive Composite Fibers

Hydrothermal Synthesis of Polyaniline Mesostructures

Relationship Between Electrical Conductivity And Phase Morphology Of Polyaniline/polyacrylonitrile And Polyaniline/polystyrene Blends

Flexible Conductive Fibers from Alginate, Cellulose Nanocrystals, and Polyaniline by Wet Spinning

Electrical Conductivity of Hollow Polyaniline Microspheres Synthesized by A Self-Assembly Method

Wet Chemical Synthesis of Entangled Nano-fibrous Conducting Polyaniline (PANI) Mesh: Effect of Heating and Stirring

Electrochemical Deposition of Polyaniline Nanosheets Mediated by Sulfonated Polyaniline Functionalized Graphenes