Abstract:Plastic production has been rapidly growing across the world and, at the end of their use, many of the plastic products become waste disposed of in landfills or dispersed, causing serious environmental and health issues. From a sustainability point of view, the conversion of plastic waste to fuels or, better yet, to individual monomers, leads to a much greener waste management compared to landfill disposal. In this paper, we systematically review the potential of pyrolysis as an effective thermochemical conversion method for the valorization of plastic waste. Different pyrolysis types, along with the influence of operating conditions, e.g., catalyst types, temperature, vapor residence time, and plastic waste types, on yields, quality, and applications of the cracking plastic products are discussed. The quality of pyrolysis plastic oil, before and after upgrading, is compared to conventional diesel fuel. Plastic oil yields as high as 95 wt.% can be achieved through slow pyrolysis. Plastic oil has a heating value approximately equivalent to that of diesel fuel, i.e., 45 MJ/kg, no sulfur, a very low water and ash content, and an almost neutral pH, making it a promising alternative to conventional petroleum-based fuels. This oil, as-is or after minor modifications, can be readily used in conventional diesel engines. Fast pyrolysis mainly produces wax rather than oil. However, in the presence of a suitable catalyst, waxy products further crack into oil. Wax is an intermediate feedstock and can be used in fluid catalytic cracking (FCC) units to produce fuel or other valuable petrochemical products. Flash pyrolysis of plastic waste, performed at high temperatures, i.e., near 1000 °C, and with very short vapor residence times, i.e., less than 250 ms, can recover up to 50 wt.% ethylene monomers from polyethylene waste. Alternatively, pyrolytic conversion of plastic waste to olefins can be performed in two stages, with the conversion of plastic waste to plastic oil, followed by thermal cracking of oil to monomers in a second stage. The conversion of plastic waste to carbon nanotubes, representing a higher-value product than fuel, is also discussed in detail. The results indicate that up to 25 wt.% of waste plastic can be converted into carbon nanotubes.

Industrial equipment and process for continuous production of engine oil from plastic wastes

Opportunities for converting waste plastics into petrochemicals: Process design, multi-objective optimization, and omnidirectional techno-economic-society-environment assessment

Investigation on thermal dechlorination and catalytic pyrolysis in a continuous process for liquid fuel recovery from mixed plastic wastes

Progress of Research on Chemical Upcycling of Plastic Waste Based on Pyrolysis

Pyrolytic Conversion of Plastic Waste to Value-Added Products and Fuels: A Review

Chemical Conversion of Fischer–Tropsch Waxes and Plastic Waste Pyrolysis Condensate to Lubricating Oil and Potential Steam Cracker Feedstocks

Research Progress in Fuel Oil Production by Catalytic Pyrolysis Technologies of Waste Plastics

Processing and utilization of the solid plastic waste oil as the sustainable substitute for fossil fuel for the CI engine from microwave assisted pyrolysis process

Synthetic bacterial consortium for degradation of plastic pyrolysis oil waste

A comprehensive experimental investigation of plastic waste pyrolysis oil quality and its dependence on the plastic waste composition

Cleaner production of aviation oil from microwave-assisted pyrolysis of plastic wastes

Valorization of PE plastic waste into lipid cells through tandem catalytic pyrolysis and biological conversion

Maximizing olefin production via steam cracking of distilled pyrolysis oils from difficult-to-recycle municipal plastic waste and marine litter

Process design and techno-economic analysis of the coproduction of oil, electricity, and protein from plastics and biomass using an integrated system

Opportunities and challenges for the application of post-consumer plastic waste pyrolysis oils as steam cracker feedstocks: To decontaminate or not to decontaminate?

Conversion of Mixed Waste Plastic into Fuel Oil Production from Pyrolysis

From Waste to Energy: Enhancing Fuel and Hydrogen Production through Pyrolysis and In-Line Reforming of Plastic Wastes

High-purity H2 Production from Mixed PVC/PET Plastic Wastes Through Tandem Hydrothermal Depolymerization and Aqueous Phase Reforming

The utilisation of oils produced from plastic waste at different pyrolysis temperatures in a DI diesel engine

Comparative Experiments on Recycling of Oil Sludge, Oil Shale and Biomass waste in a Continuous Rotating Pyrolysis Reactor

Experimental study, simulation and technical–economic feasibility of an interesterification plant for hydrocarbons synthesis by using plastics and frying oil waste