Abstract:In this study, the cooperative effect of Mg and Si contents on the microstructural evolution, mechanical properties, and deformation behavior of the cast Al–Li–Mg–Si alloys is investigated. Five different Al–Li–Mg–Si alloys are prepared by conventional casting method, which are referred to as Alloy A-E. The results show that with the increase in the Mg content, the amount of lath-like Mg2Si precipitates and bulk-like AlLiSi particles increases, which leads to an improvement in the strength and ductility of alloys. The amount of intergranular Si-rich phases in Alloy D increases with the increase in the Si content. Further, a higher Si content in Alloy E promotes the formation of bulk-like AlLiSi. The geometric phase analysis (GPA) results reveal strain partitioning behavior at the interface of Mg2Si precipitates and AlLiSi particles, which follows the Orowan looping or dislocation cutting strengthening mechanism. The geometrically necessary dislocation (GND) density calculation results suggest that the lath-like Mg2Si precipitates play a critical role in the deformation behaviors of Alloy A-C. The hindering effect of lath-like Mg2Si precipitates on the movement of dislocations decreases the GND density gap between high-angle grain boundaries or junctions and grain interior and improves the resistance to deformation. However, the deformation behaviors of Alloy D and E with higher Si content are mainly governed by the intergranular Si-rich phases. Finally, a methodological framework is established to elucidate the effect of precipitates and/or intergranular phases on the deformation behaviors of materials using a combination of GPA and GND density calculation methods.

Microstructure and mechanical properties of magnesium alloys containing Ca and Si

As-Cast Microstructure and Its Formation Mechanism in Mg-Based Alloys Containing Ca and Si

Microstructure and Mechanical Properties of Heat Resistant Mg-Zn-Si-Ca Ahoy

Effects of Ca and Si Compound Alloying on Microstructure of AZ31 Magnesium Alloy

Regulative Effect of Mg/Si Ratio on Microstructure Evolution and Mechanical Properties of Cast Al-Li-Mg-Si Alloys

Effects of Zr and Mg alloying on microstructure and properties of Cu-Cr-Si alloys

Microstructure and Mechanical Extruded Properties of Extruded AM50+xCa Magnesium Alloys

Effects of Si content on microstructure and mechanical properties of Mg-Gd-Y-Zr casting alloy

Effect of Mg addition on microstructure and mechanical properties of Al-Si-Cu-Fe alloy with squeeze casting

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

Influence of Ca on microstructure and mechanical properties of ZA63 magnesium alloy

Influence of Si on the mechanical properties and high temperature creep properties of AM50 magnesium alloy

Influence of Varied Mg/Si Mass Ratio on the Microstructure and Mechanical Properties of Aluminum Die Casting Alloys

Cooperative Effect of Mg and Si Contents on the Microstructural Evolution, Mechanical Performance, and Deformation Behavior of Cast Al–Li–Mg–Si Alloys

Mechanical Properties and Creep Behavior of Mg–Al–Ca Alloys

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Development of microstructure in solution-heat-treated Mg-5Al-<i>x</i>Ca alloys

Influence of Grain Size on Microstructure, Mechanical Properties and Strain Hardening Behavior of Mg-0.3Ca (wt.%) Alloy

Microstructure Refinement of Mg-Al-Zn-Si Alloys

Effects of silicon on microstructure, fluidity mechanical properties, and fracture behaviour of Mg-6Alalloy

The Role of Ca on the Microstructure and Tensile Properties of Mg-Al-Zn-Ca Alloys