Abstract:Abstract Al–Zn–Mg–Cu–Zr aluminum alloys have shown promise as materials for drill pipes; however, their application temperature is limited to below 120°C. This study investigates the influence of incorporating the rare earth element Nd on the microstructure and mechanical properties of Al–Zn–Mg–Cu–Zr alloys. The microstructural evolution during casting, homogenization, hot deformation, and heat treatment processes is characterized using optical microscopy and scanning electron microscopy. The composition of the rare earth phase is determined through transmission electron microscopy (TEM). Furthermore, first-principles calculations are employed to determine the formation enthalpy, cohesive energy, shear modulus, bulk modulus, Young’s modulus, and Poisson’s ratio of bulk Al 8 Cu 4 Nd. The effect of Nd addition on the mechanical properties of the alloy is investigated through hardness and tensile testing. The results indicate that the addition of Nd significantly refines the grain and dendrite sizes of the alloy and effectively suppresses recrystallization behavior during hot extrusion and solution treatment. TEM observations reveal the presence of micrometer-sized blocky Al 8 Cu 4 Nd phases and nanometer-sized Al 3 Nd phases. The Al 3 Nd phases are located near dislocations, hindering dislocation movement and thus enhancing the alloy’s mechanical properties. First-principles calculations demonstrate that the bulk Al 8 Cu 4 Nd phase exhibits superior structural stability, deformation resistance, and brittle characteristics, which negatively impact the ductility of the alloy. The alloy with Nd addition can maintain a high hardness value for an extended period at high temperature, and the tensile strength of the alloy with 0.26 wt% Nd addition reaches 396.2 MPa at 120°C. These results indicate that the rare earth element Nd can improve the high-temperature mechanical properties of the alloy.

Influence of Nd on the mechanical properties and high temperature creep properties of AM50 magnesium alloy

Influence of Alloying Agents on Properties of AM60B Magnesium Alloy

Effect of Alloying with Al, Nd and Ca and Heat Treatment on Microstructures and Mechanical Properties of Vacuum Die-Cast AM50 Alloy

Effect of substituting Gd with 3 wt.% Nd on high temperature creep behaviors of peak-aged Mg-10Gd-0.4Zr casting Mg alloy

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Enhanced Grain Refinement and Precipitation of the IEECAPed Mg-Sm-Zn-Zr Alloy by Nd Addition

Microstructure and Mechanical Properties of Mg–4.5Zn–xNd (x=0, 1 and 2, Wt%) Alloys

Effect of Nd addition on the microstructure and mechanical properties of extruded Mg-Gd-Zr alloy

The effect of Y and Nd additions on the microstructure and creep behavior of AZ80

Microstructures and Mechanical Properties of As-Cast Mg–5Al–0.4Mn–xNd (x = 0, 1, 2 and 4) Alloys

Effect of the precipitation state on high temperature tensile and creep behaviors of Mg-15Gd alloy

Effect of rare earth Nd on the microstructural transformation and mechanical properties of 7xxx series aluminum alloys

Microstructure and Mechanical Properties of Extruded Mg-Zn-Nd-Y-Zr-Ca Alloy

Effect of Substituting Nd for Y on Microstructure and Mechanical Properties of Mg-7Y-2Al Alloy

Achieving superior elevated-temperature strength of Mg-12Gd-3Y alloys by Nd addition

Effects of rare earth neodymium (Nd) and heat treatment on anti-corrosion behaviors of the AZ80 magnesium alloy

Microstructure and mechanical behaviour of an elevated temperature Mg-rare earth based alloy

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Study on the Creep Properties and Microstructures of EW75 Alloy

Effect of Microalloying Rare-Earth Nd on Microstructure Evolution and Mechanical Property of Cu Alloy