Abstract:A microstructure composed of martensite matrix, lower bainite, and stable film-like austenite was designed by a quenching and isothermal bainitic holding process in a 0.30C–2.69Mn–1.71Si (wt.%) steel. The yield strength, tensile strength, and ductile-to-brittle transition temperature (DBTT) of the high-strength steel thus obtained were 1263 MPa, 1521 MPa, and − 33 °C, respectively, and at − 20 °C, it showed superior low-temperature toughness, which reached 77.5 J/cm2. Meanwhile, it showed excellent hydrogen embrittlement (HE) resistance, and the total elongation loss is only 3.1% after 15 min of hydrogen charging. The excellent comprehensive performance is attributed to the fact that fine stable austenite with film-like morphology hindered the crack nucleation and propagation, and hindered hydrogen diffusion as a hydrogen trap. However, with a decrease in the isothermal temperature, transition carbide precipitation was accompanied by a further decrease in austenite grain size. For this condition, although transition carbides can act as effective hydrogen traps, excessive precipitation decreased the carbon content of retained austenite and increased the deformation heterogeneity between austenite and martensite matrix, leading to weakened austenite stability and HE resistance, a total elongation loss of approximately 39% (15 min hydrogen charging), a sharp decrease in impact toughness, and an increase in DBTT. The competitive role of film-like austenite and transition carbides on the comprehensive mechanical performance of steel is revealed, especially the suppression of crack nucleation and propagation that will provide a guide for the design of high strength steels with excellent impact toughness and HE resistance.

Interaction of Hydrogen and Retained Austenite in Bainite/Martensite Dual-Phase High Strength Steel

Hydrogen Trapping in Bainite/Martensite Dual-phase High Strength Steel

The finding of hydrogen trapping at phase boundary in austenitic stainless steel by scanning Kelvin probe force microscopy

Experimental and numerical analysis of hydrogen diffusion behaviors in an ultra-fine bainitic steel

Quantitative investigation on deep hydrogen trapping in tempered martensitic steel

Atomic-scale insights on hydrogen trapping and exclusion at incoherent interfaces of nanoprecipitates in martensitic steels

Competitive role of film-like austenite and transition carbides on hydrogen embrittlement resistance and impact toughness in bainite-containing quenched and partitioned steel

Effect of Morphology for Novel Bainite/Martensite Dual-Phase High Strength Steel on Its Hydrogen Embrittlement Susceptibility

A new perspective on hydrogen diffusion and hydrogen embrittlement in low-alloy high strength steel

Atom Probe Tomographic Observation of Hydrogen Trapping at Carbides/ferrite Interfaces for a High Strength Steel

Hydrogen influence on some advanced high-strength steels

Interrelationship between hydrogen and α′-martensite of SUS 304 austenitic stainless steel revealed by tensile tests

Towards Quantitative Analysis of Deuterium Absorption in Ferrite and Austenite during Electrochemical Charging by Comparing Cyclic Voltammetry and Cryogenic Transfer Atom Probe Tomography

Difference of Hydrogen Diffusion Regularity Between Interstice-Doped and Substitution-Doped Formed by Steel Carburizing

Phase-Field Modeling of Hydrogen Diffusion and Trapping in Steels

Interaction of Hydrogen with the Microstructure of AH36 Steel

Hydrogen Permeation in X65 Steel under Cyclic Loading

Hydrogen embrittlement and hydrogen diffusion behavior in interstitial nitrogen-alloyed austenitic steel

Effect of Strain-Induced Martensite on Hydrogen Embrittlement of Austenitic Stainless Steels Investigated by Combined Tension and Hydrogen Release Methods

Influence of the interaction of hydrogen with the phase boundary of duplex stainless steel on corrosion

Morphological effect of retained austenite microstructure on hydrogen diffusion under contact loading of bearings