Abstract:Due to native deficiency of the interfacial mismatch between Al2O3 and Al-melt, as well as micron-Al2O3 segregation at matrix grain boundaries (GBs), achieving both high strength and fracture toughness has been the long-lasting challenge for Al-CuO composite fabricated by conventional casting. Herein, we report a novel manufacturing of Al-CuO composite via shift-speed ball-milling (SSBM) of Al-5 wt.% CuO powders and afterwards subjected to hot-pressing (HP) as well as heat treatment. Comprehensive characterization shows that in-situ generation of the two types of Al2O3 with intragranular distribution, including δ*-Al2O3 particles (∼200 nm) and γ-Al2O3 whiskers (length of ∼150 nm, thickness of ∼20 nm), was governed by a diffusion-assisted nucleation-regime ascribing to the intense thermal effect of Al-CuO reaction. The size and spatial distribution of Al2O3 were emphasized to address their contribution to the high mechanical performance of the composite, which exhibits a tensile strength of ∼481 MPa and fracture elongation of ∼16.8 %. Meanwhile, the toughening mechanism of present Al-CuO composite was rationalized on basis of the "dislocation punched zone" and "plastic zone" affected by Al2O3. Both the theoretical analysis and fracture morphology support a reinforcements-matrix interface failure mechanism and the non-uniform distribution of Al2O3 consisting alternant "rich/poor zones" can markedly contribute to the high toughness. The present findings may provide a promising strategy to achieve an intragranular distribution of nano-sized reinforcements in Al-metal oxides composites, which enables increasing strength and ductility of the metal matrix.

Tensile deformation and fracture behavior of Cu-0.54A12O3 dispersion strengthened copper alloy

Deformation and Fracture Behavior of Electrocodeposited Alumina Nanoparticle/Copper Composite Films

High Temperature Tensile Properties of Al2O3/Cu Composite

Microstructure, Properties and Strengthening Mechanism of Cu-Tib2-Al2o3 Composite Prepared by Liquid Phase In-Situ Reaction Casting

Microstructure and hot deformation behavior of nano and micron hybrid Al2O3 particles dispersion strengthened copper base composites

Microstructure evolution and properties of Cu–Ag microcomposites with different Ag content

Study on strengthening and toughening mechanisms of cu/Al composites dominated by interface layer

In-situ solid-state deformation-driven rapid reaction towards higher strength-ductility Al-CuO composites

Role of Cu on the Mechanical Properties and Microstructures Evolution of Al-xCu-1Li-0.4Mg–1Zn-0.1Zr Alloys

Mechanical Properties and Fracture Behavior of Cu-Co-Be Alloy after Plastic Deformation and Heat Treatment

Strain Strengthening Of Ag-10cu In Situ Filamentary Composite Prepared By Heavy Deformation

Properties of Cu and Fe under Large Deformation and Strength Calculation of Cu-11.5% Fe in Situ Composites

Evolution of the Second-Phase Particles and Their Effect on Tensile Fracture Behavior of 2219 Al-xCu Alloys

Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction

Synergetic strengthening effects on copper matrix induced by Al2O3 particle revealed from micro-scale mechanical deformation and microstructure evolutions

Enhanced Tensile Ductility and Toughness in Nanostructured Cu

Investigation of the Microstructure and Mechanical Properties of Copper-Graphite Composites Reinforced with Single-Crystal α-Al2O3 Fibres by Hot Isostatic Pressing

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Microstructure and Compressive Deformation Behavior of As-Cast CrFeCoNiCux High Entropy Alloys

Effect of Heating Process on Fracture Behaviors of Wf/Cu82Al10Fe4Ni4 Composites