Abstract:Lean Blowout (LBO) performance is very important to the aero and ground gas turbine combustors. A typical liquid-fueled gas turbine combustor is the one with swirl cup dome which plays an important role to the LBO. The swirl cup dome comprises swirlers and nozzle usually. The swirlers serve to generate a toroidal flow reversal that entrains and recirculates a portion of the hot combustion products to mix with the incoming fresh air and fuel, so it makes the recirculation region the sustainable source of ignition. Swirlers in present study generally are two or three stages, and the nozzle takes different atomization styles, such as pressure-swirl atomization, prefilming and airblast atomization. Different swirlers matching various nozzles form all kinds of swirl cup domes, and each swirl cup dome of combustor would have different LBO performance and other combustion properties resulting from its structure characteristics. The flow flux arrangement and spray distribution are the two important factors to determine the combustor performance. Two combustor dome test rigs were investigated, of which one comprises with three air swirlers and a fuel prefilming nozzle (dome A), and the other is composed of two air swirlers and a fuel pressure nozzle (dome B). Tests were conducted to get the LBO fuel air ratio at atmospheric pressure. To explain the experimental results, numerical simulations were performed for cool flow fields of two combustors, also the cold flow field and spray of the two combustors’ dome downstream were measured by PDA with water instead of kerosine. The flame pictures near LBO were taken. The preliminary results indicated that the combustor with dome A had better spray uniformity than the one with dome B, but it had a little worse LBO performance. The air flow mass percentage of the inner swirler of dome A should decrease to some extent in order to establish a lower pressure region at the outlet of dome A, which would be helpful to decrease the LBO fuel air ratio and so as to improve the LBO performance. The two domes had their own advantages, and if the benefits of both were integrated, it was possible to design a better swirl cup dome.

The Effect of Flow Field and Fuel Spray of Combustor with Swirl Cup on Lean Blowout Limit at Idle Condition

Study on the Effects of Dome Fuel Distribution Ratio on Lean Blowout of a Model Combustor

A Study on Lean Blowout of Multi-vortexes-dome Model Combustor

LBO Performance Comparison Between Two Combustors with Different Swirl Cups

Analysis on Lean Blowout of Swirl Cup Combustor at Atmospheric Pressure Condition

Effect of confinement ratio on flame structure and blow-off characteristics of swirl flames

Effect of Pilot-Inner-Staged Swirl on Ignition and Blowout Performance of Combustor

Lean Blowout Performance of CO in Swirl Combustor Under Atmospheric Pressure Condition

Experiment and Simulation Study on Lean Blow-Out of Trapped Vortex Combustor with Various Aspect Ratios

Numerical Simulation of Effects of Venturi Tube Throat Diameter on Flow Field of Combustor

Improving Blowout Performance of the Conical Swirler Combustor by Employing Two Parts of Fuel at Low Operating Condition

A Preliminary Study on Lean Blowout of One Combustion Stability Device

Effects of flow-flame interactions on the stabilization of ultra-lean swirling CH<sub>4</sub>/H<sub>2</sub>/air flames

The Effects of Strong-Weak Swirling Interaction on Emissions in a Multi-Nozzle Combustor

Computational Study of the Effect of Dual Air Swirling Injection on Turbulent Combustion of Kerosene–Air at a High Pressure

The Effects of Strong-Weak Swirling Interaction on Emissions In a Multi- Nozzle Model Combustor

Investigation on Bluff-Body and Swirl Stabilized Flames Near Lean Blowoff with PIV/PLIF Measurements and LES Modelling

Effect of Swirl Number on the Premixed Flame Blowout Performance of the Low Calorific Value Gas not Containing Hydrogen

Swirling flow and spray atomization interactions in a swirl cup airblast fuel injector: Outer swirler effect

Effect of Fuel Reactivity on Flame Properties of a Low-Swirl Burner

The Effect of Swirl Number on Lean Blow Out Limits of Lean Direct Injection Combustors