Abstract:Abstract Nickel-base superalloys (NBSAs) are extensively utilized as the design materials to develop turbine blades in gas turbines due to their excellent high-temperature properties. Gas turbine blades are exposed to extreme loading histories that combine high mechanical and thermal stresses. Both directionally solidified (DS) and single crystal NBSAs are used throughout the industry because of their superior tensile and creep strength, excellent low cycle fatigue (LCF), high cycle fatigue (HCF), and thermomechanical fatigue (TMF) capabilities. Directional solidification techniques facilitated the solidification structure of the materials to be composed of columnar grains in parallel to the <001> direction. Due to grains being the sites of failure initiation the elimination of grain boundaries compared to polycrystals and the alignment of grain boundaries in the normal to stress axis increases the strength of the material at high temperatures. To develop components with superior service capabilities while reducing the development cost, simulating the material’s performance at various loading conditions is extremely advantageous. To support the mechanical design process, a framework consisting of theoretical mechanics, numerical simulations, and experimental analysis is required. The absence of grain boundaries transverse to the loading direction and crystallographic special orientation cause the material to exhibit anisotropic behavior. A framework that can simulate the physical attributes of the material microstructure is crucial in developing an accurate constitutive model. The plastic flow acting on the crystallographic slip planes essentially controls the plastic deformation of the material. Crystal Visco-Plasticity (CVP) theory integrates this phenomenon to describe the effects of plasticity more accurately. CVP constitutive models can capture the orientation, temperature, and rate dependence of these materials under a variety of conditions. The CVP model is initially developed for SX material and then extended to DS material to account for the columnar grain structure. The formulation consists of a flow rule combined with an internal state variable to describe the shearing rate for each slip system. The model presented includes the inelastic mechanisms of kinematic and isotropic hardening, orientation, and temperature dependence. The crystallographic slip is accounted for by including the required octahedral, cubic, and cross slip systems. The CVP model is implemented through a general-purpose finite element analysis software (i.e., ANSYS) as a User-Defined Material (USERMAT). Uniaxial experiments were conducted in key orientations to evaluate the degree of elastic and inelastic anisotropy. The temperature-dependent modeling parameter is developed to perform non-isothermal simulations. A numerical optimization scheme is utilized to develop the modeling constant to improve the calibration of the model. The CVP model can simulate material behavior for DS and SX NBSAs for monotonic and cyclic loading for a range of material orientations and temperatures.

Crystalline Thermo Visco-Plastic Deformation and Damage of Directionally Solidified Turbine Blade

Dependence of Microstructural Evolution on the Geometric Structure for Serviced DZ125 Turbine Blades

Microstructure Degradation of Service-Exposed Turbine Blades Made of Directionally Solidified DZ125 Superalloy

Physically-based modeling of cyclic softening and damage behaviors for a martensitic turbine rotor material at elevated temperature

Direct Investigation on High Temperature Tensile and Creep Behavior at Different Regions of Directional Solidified Cast Turbine Blades

Creep life prediction for a nickel-based single crystal turbine blade

Modified crystal plasticity constitutive model considering tensorial properties of microstructural evolution and creep life prediction model for Ni-based single crystal superalloy with film cooling hole

Creep analysis and service life prediction of turbine blade with progressive damage

Crystal plasticity constitutive model and thermodynamics informed creep-fatigue life prediction model for Ni-based single crystal superalloy

Multiaxial creep–fatigue failure mechanism and life prediction of a turbine blade based on a unified numerical solution approach

Modeling of Unidirectional Growth in a Single Crystal Turbine Blade Casting

Numerical Simulation of Thermal Stress During Directional Solidification of Simple Hollow Turbine Blades

Numerical Simulation of Directional Solidification of Single Crystal Turbine Blade Casting

Crystal Visco-Plastic Model for Directionally Solidified Ni-Base Superalloys Under Monotonic and Low Cycle Fatigue

Modeling and experimental study on deformation prediction of thin-walled turbine blades during investment casting process

Stress Analysis and Deformation Prediction of a Heavy Hydraulic Turbine Blade Casting During Casting and Heat Treatment

Damage Analysis and Start-Up Schedule Optimization of Steam Turbine Rotors With an Anisotropic Damage Coupled Viscoplastic Constitutive Model

Thermomechanical fatigue behavior and failure mechanism of a nickel-based directional solidification column crystal superalloy

Modeling of directional solidification process of superalloy turbine blade castings

Microstructure Evolution and Mechanical Behaviors of Alumina-Based Ceramic Shell for Directional Solidification of Turbine Blades

Dimensional Control of Nickel-Based Single Crystal Turbine Blade Investment Casting by Process Control Optimization