Abstract:Since the discovery of efficient organic light emitting devices (OLEDs), there has been considerable interest in developing OLEDs with high brightness, high efficiency, and long lifetime for display applications. This has resulted in substantial research activity to increase the carrier mobility, color gamut, and electroluminescence efficiency of organic materials, as well as to improve electron and hole injection by the contacts. The brightness and efficiency of OLEDs depend on the number density of electrons and holes in the emission layer, so that effective charge injection into the organic materials is critical for optimum device performance. For the hole injecting contact, indium tin oxide (ITO) is often used because of its transparency and high work function (5 1eV). On the other hand, an efficient electron injecting contact is usually a low work function material such as magnesium, calcium, or lithium. These materials are typically alloyed with metal such as aluminum or silver to form contact that is both more stable and more resistant to corrosion upon exposure to air. At the same time inserting an insulating layer between cathode and organic material is effective means to improve current injection and EL. In this paper, some multilayers OLEDs were fabricated using Al,LiF/Al and Mg∶Ag as cathode respectively while ITO-coated glass as anode, 1,2,3,4,5 pentaphenyl 1,3 cyclopentadiene(PPCP) as emitter, N,N′ diphenyl N,N′ bis(3 methyl phenyl) (1,1′ biphenyl) 4,4′ diamine(TPD) as hole transport layer, tris(8 hydroxyquinoline)aluminum(Alq), 2 (4 biphenylyl) 5 (4 tertbutyl phenyl) 1,3,3 oxadiazole(PBD) or 2,5 bis(5 tert butyl 2 benzoxazolyl)thiophene(BBOT) as electron transport layer, respectively. And effect of cathode on performance of blue OLEDs was studied. All organic layers were prepared by a high vacuum multisource type organic molecular deposition system. From result, it is found that the performance of device with LiF/Al as cathode excels that of the device with Al or Mg:Ag as cathode. Devices with LiF/Al show better I V characteristics and higher EL efficiency . The presence of LiF at the metal organic material interface cause band bending of organic material, thus lower the electron injection barrier height.

Effect of the CsCl Buffer Layer on the Performances of the Organic Electro-Luminescent Devices

Effect of Nacl Buffer Layer on the Performance of Organic Light-Emitting Devices (Oleds)

Enhanced Properties of Organic Electroluminescent Devices with Cesium Chloride Ultra-Thin Layer

Improved performance of organic light-emitting diodes with cesium chloride inside tris (8-hydroxyquinoline) aluminum

The Effect of Alkaline Metal Chlorides on the Properties of Organic Light-Emitting Diodes

Improvement of Electron Injection of Organic Light-Emitting Devices by Inserting a Thin Aluminum Layer into Cesium Carbonate Injection Layer

The Effect of Various Electrodes on the Properties of Electroluminescent Devices with Potassium Chloride Inside Tris (8-Hydroxyquinoline) Aluminum

Effect of Cathode on Performance of Blue Organic Electroluminescence Device

Enhancement of Electron Injection in Organic Light-Emitting Devices Using an Ag/LiF Cathode

Effect of LiF Buffer Layer on the Performance of Organic Electroluminescent Devices

A Novel Electron Injection Layer with Co-evaporating Tris(8-hydroxyquinoline)Aluminum Doped Cesium Carbonate in Organic Light-emitting Diodes

Improving the Performance of Organic Light-Emitting Devices by Incorporating Non-Doped TCNQ As Electron Buffer Layer

Enhanced Brightness of Organic Light-Emitting Diodes Based on Mg:Ag Cathode Using Alkali Metal Chlorides As an Electron Injection Layer

Enhanced Electron Injection in Organic Light-Emitting Devices by Using a Composite Electron Injection Layer Composed of 8-Hydroquinolatolithium and Cesium Oxide

A Novel Buffer Layer of Alq(3) in Organic Electroluminescent Devices

Efficient Organic Light-Emitting Diodes with C60 Buffer Layer

The Effect Of Electrode Materials On The Performance Of Oleds

Aluminum Phthalocyanine Chloride As a Hole Injection Enhancer in Organic Light-Emitting Diodes

Effect of Liq as an Electron Injection Layer on Organic Electroluminescent Devices

Electron injection and electroluminescence investigation of organic light-emitting devices based on a Sn/Al cathode

Organic Light-Emitting Diodes Using Potassium Chloride As Efficiency and Stability Enhancers